manualshive.com logo in svg

Ford 2010 Milan Hybrid, Owner'S Manual

The Ford 2010 Milan Hybrid is an innovative and eco-friendly sedan that combines the power of a gasoline engine with the efficiency of electric motors. Enhance your driving experience with our Quick Reference Manual, available for free download at manualshive.com, providing essential information to maximize your vehicle's performance.

Share
Download
background image

Your vehicle is equipped with the AdvanceTrac

威

system. The

AdvanceTrac

威

system provides the following stability enhancement

features for certain driving situations:

•

Traction Control (TCS), which functions to help avoid drive-wheel
spin and loss of traction.

•

Electronic Stability Control (ESC), which functions to help avoid skids
or lateral slides

The AdvanceTrac

威

system automatically enables each time the engine is

started. All features of the AdvanceTrac

威

system (TCS and ESC) are

active and monitor the vehicle from start-up. However, the system will
only intervene if the driving situation requires it.

The AdvanceTrac

威

system includes

an AdvanceTrac

威

“OFF” control

switch on the center of the
instrument panel, a “sliding car”
icon

and a “sliding car off”

icon

in the instrument cluster.

Both the “sliding car” icon

and the “sliding car off” icon

in the

instrument cluster will illuminate temporarily during start-up as part of a
normal system self-check. The “sliding car” icon

may illuminate

(flash) during certain driving situation which cause the AdvanceTrac

威

system to operate. If the “sliding car” icon

illuminates steadily, have

the system serviced by an authorized dealer immediately. If equipped
with a message center, the vehicle will also indicate a failure with the
AdvanceTrac

威

system.

When AdvanceTrac

威

performs a normal system self-check, some drivers

may notice a slight movement of the brake, and/or a rumble, grunting, or
grinding noise after startup and when driving off.

When an event occurs that activates AdvanceTrac

威

you may experience

the following:

•

A slight deceleration of the vehicle

•

The “sliding car”

indicator light will flash.

•

If your foot is on the brake pedal, a vibration in the pedal

•

If the driving condition is severe and your foot is not on the brake, the
brake pedal may move as the systems applies higher brake forces. You
may also hear a whoosh of air from under the instrument panel during
this severe condition.

•

The brake pedal may feel stiffer than usual.

2010 Milan

(mln)

Owners Guide, 1st Printing
USA

(fus)

Driving

201

Summary of Contents for 2010 Milan Hybrid







































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan Hybrid

Back View RV-250 User Manual preview
RV-250
Brand: Back View Pages: 168
OEM Tools 22505 Operating Instructions And Parts Manual preview
22505
Brand: OEM Tools Pages: 4
PAC SWI-RC Installation Instructions preview
SWI-RC
Brand: PAC Pages: 4
PAC RP4-CH11 Manual preview
RP4-CH11
Brand: PAC Pages: 4
PAC BCI-CH41 User Manual preview
BCI-CH41
Brand: PAC Pages: 8
PAC C2R-CHY4 Installation Instructions preview
C2R-CHY4
Brand: PAC Pages: 5
Napoli NPL-TV 7874 DIGITAL Instruction Manual preview
NPL-TV 7874 DIGITAL
Brand: Napoli Pages: 20
Farad BARS PR25 - 2 Quick Start Manual preview
BARS PR25 - 2
Brand: Farad Pages: 8
ideus VV950 User Manual preview
VV950
Brand: ideus Pages: 159
ULTIMATE SPEED 285690 Assembly And Safety Advice preview
285690
Brand: ULTIMATE SPEED Pages: 10
Quadratec QuadraTop 11051.0415 Installation Manual preview
QuadraTop 11051.0415
Brand: Quadratec Pages: 8
Packard 1948 eight Operating Instructions Manual preview
1948 eight
Brand: Packard Pages: 25
Thule Kit 1312 Instructions Manual preview
Kit 1312
Brand: Thule Pages: 8
SSV Works RG4-DM3 Manual preview
RG4-DM3
Brand: SSV Works Pages: 2
Husky 31564 Assembly, Installation, Operation And Maintenance Instructions preview
31564
Brand: Husky Pages: 8
Cadillac 2011 Cadillac Owner Assistance Information preview
2011 Cadillac
Brand: Cadillac Pages: 48
Skoda 2015 Superb Owner'S Manual preview
2015 Superb
Brand: Skoda Pages: 276
Subaru impreza 2017 Owner'S Manual preview
impreza 2017
Brand: Subaru Pages: 786

Brands by name

Popular brands

Load more brands