manualshive.com logo in svg

Folyon H300P, User Manual

The Folyon H300P User Manual is available for free download from manualshive.com. This comprehensive manual provides step-by-step instructions and in-depth information about operating and maintaining the H300P. Get the most out of your product with this helpful manual, easily accessible and ready for download at manualshive.com.

Share
Download
background image

 

H300P Temperature Humidity Chamber

 

 

Page 3 

 

 

CAUTION

: This chamber is designed for operation in a conditioned laboratory environment. Operation 

above 30°C (85°F) or below 16°C (60°F) ambient room temperature is NOT recommended. 

Operation Safety Notices 

 

CAUTION

: The Watlow “PM PLUS 6 User’s Manual” is a general manual and is written for a wide variety 

of applications and configurations. Not all features or functions are applicable.  

 

CAUTION

: The PM PLUS 6 Controllers have been properly configured at our factory to match the 

chamber’s system requirements and to perform optimally over a wide range of operating 
conditions. Improper modifications to these setup values can result in erratic performance 
and unreliable operation.  Do not attempt to modify the setup values, unless you thoroughly 
understand what you are doing.  If there is any doubt, please contact the Folyon 
Technologies before proceeding. 

 

CAUTION

: Avoid touching the sensor assembly inside the chamber.  

 

WARNING

: Do NOT put items in the chamber that could burn or explode. This is NOT an explosion-proof 

chamber. 

 

WARNING

: Do NOT put items in the chamber which can emit corrosive vapors or substances. 

 

WARNING

: This chamber is NOT a curing oven. There are NO provisions for venting fumes. 

 

WARNING

:  Always unplug the chamber from the outlet when filling the water reservoir with water.  If 

water is spilled inside the chamber, do not plug in!  Allow sufficient time (at least 24 hours) 
for the water to dry. 

 

WARNING

: 

The chamber is designed to operate in not condensing conditions only. It is up to the 

operator to ensure that condensation does not occur inside the chamber. Condensation 
inside the chamber can damage the sensors and the internal components of the chamber. 
Operating the chamber when condensation is present inside the chamber will void the 
warranty!

  

 

WARNING

: 

Before the chamber is shipped using a common carrier such as UPS, FexEx, DHL and the 
Postal Service, all water must be emptied from the water reservoir.  The water can be 
emptied by tilting the chamber and emptying all the water into a bucket, through the 
filling tube. Make sure the unplug the chamber before filling or emptying water.

 

Summary of Contents for H300P

















Reviews:

No comments

Related manuals for H300P

Brands by name

Popular brands

Load more brands