manualshive.com logo in svg

Folyon H300P, User Manual

The Folyon H300P User Manual is available for free download from manualshive.com. This comprehensive manual provides step-by-step instructions and in-depth information about operating and maintaining the H300P. Get the most out of your product with this helpful manual, easily accessible and ready for download at manualshive.com.

Share
Download
background image

 

H300P Temperature Humidity Chamber

 

 

Page 12 

 

Linearization Menu 

For the relative humidity controller there are no changes to controller default parameters.  For the 
temperature controller, each H300P chamber is supplied with its own set of Linearization Menu 
settings.  These settings are included in a document on the flash drive that comes with each 
chamber. 

Process Value Menu 

 

No changes to controller default parameters. 

Control Loop Menu 

Most of the parameters in the Control Loop Menu are specific to each H300P chamber.  Each H300P 
chamber is supplied with its own set Control Loop Menu settings.  These settings are included in a 
document on the flash drive that comes with each chamber. 

Output Menu 

Output 1 

Parameter 

Temperature 

Humidity 

Output Function 

Heat 

Heat 

Time Base Type 

Fixed Time Base  Fixed Time Base 

Fixed Time Base 

1.0 

3.0 

Low Power Scale 

0 

0 

High Power Scale 

100 

50 

Output 2 

Parameter 

Temperature 

Humidity 

Output Function 

Cool 

Cool 

Time Base Type 

Fixed Time Base  Fixed Time Base 

Fixed Time Base 

1.0 

3.0 

Low Power Scale 

0 

0 

High Power Scale 

100 

100 

 

Alarm Menu 

 

No changes to controller default parameters. 

Function Key Menu 

 

No changes to controller default parameters. 

Summary of Contents for H300P

















Reviews:

No comments

Related manuals for H300P

Brands by name

Popular brands

Load more brands