manualshive.com logo in svg

Folyon H300P, User Manual

The Folyon H300P User Manual is available for free download from manualshive.com. This comprehensive manual provides step-by-step instructions and in-depth information about operating and maintaining the H300P. Get the most out of your product with this helpful manual, easily accessible and ready for download at manualshive.com.

Share
Download
background image

 

H300P Temperature Humidity Chamber

 

 

Page 11 

 

•

 

Press the Home key when done. 

To turn the control back On follow these steps: 

•

 

Press the Forward Arrow key once.  

Control Mode 1

 should be highlighted. 

•

 

Press the Forward Arrow key once. 

•

 

Press the 

+

 or 

–

 key until 

Auto

 is highlighted. 

•

 

Press the Home key when done. 

Setting Up a Profile (PM6R Models Only) 

For instructions on how to set a profile, see the “PM Plus User’s Manual”, Chapter 6:  Profiles. For easy 
profile setup download the Watlow EZ-LINK™ App to your phone or tablet. The App communicates with the 
controllers using Bluetooth®. 

Setup Page Parameters 

The setup page parameters below have been programmed into the temperature and humidity controllers at 
the factory.  These parameters are for reference only and should not be modified. 

Improper modifications to these setup values can result in erratic performance and unreliable operation. Do 
not attempt to modify the setup values, unless you thoroughly understand what you are doing. 

These parameters were saved at the factory under User Settings 1.  If these parameters are modified, they 
can be restored to factory defaults. Please see the 

Restoring Factory Default Parameters

 section in this 

manual on how to do this. 

Analog Input Menu 

Parameter 

Temperature 

Humidity 

Sensor Type 

RTD 100 Ohm 

Milliamps 

RTD Leads 

3 

 

Units 

 

Relative Humidity 

Scale Low 

 

4.00 

Scale High 

 

20.00 

Range Low 

 

0.0 

Range High 

 

100.0 

Process Error Enable 

 

Off 

Filter  

0.5 

0.5 

Input Error Latching 

Off 

Off 

Display Precision 

Tenths 

Tenths 

Calibration Offset 

0.0 

0.0 

Summary of Contents for H300P

















Reviews:

No comments

Related manuals for H300P

Aralab FITOCLIMA 2500 HP User Manual preview
FITOCLIMA 2500 HP
Brand: Aralab Pages: 73

Brands by name

Popular brands

Load more brands