background image

 

H300P Temperature Humidity Chamber

 

 

Page 16 

 

Folyon Technologies Inc. Limited Warranty 

Folyon Technologies Inc. (Folyon) warrants the H300P Chambers (Equipment) manufactured by Folyon and supplied 
under this contract to be free from defects in materials and workmanship under normal use and proper maintenance. 

Folyon will repair or replace any defective part, not excluded in this limited warranty, for a period of ONE YEAR from 
the date of invoice. Folyon reserves the right to require the Equipment be returned, freight prepaid, to Folyon’s factory 
or to inspect any defective part at the Purchaser’s site. Folyon shall have sole discretion to determine whether any part 
is defective and whether any defective part will be repaired or replaced. This limited warranty shall extend to any 
standard chamber accessory and component part which is normally sold by Folyon. Non-standard accessories and 
component parts specified by the Purchaser shall be warranted only to the extent of the original manufacturer’s 
warranty, if any exists.  Purchaser shall notify Folyon in writing of any alleged defect within 10 days after its discovery 
within the warranty period.  

Following the ONE YEAR parts and labor warranty, the Purchaser will be responsible for the cost of all replacement 
parts. Folyon will provide a lifetime labor warranty for the original purchaser of the Equipment. 

The following parts are excluded from this limited warranty and are sold as-is or are considered expendable:  paint and 
cosmetic surface finishes and treatments, port plugs, desiccant. 

This limited warranty shall extend in full to Equipment installed within continental United States and Canada. For all 
other locations, Purchaser is responsible for all shipping costs associated with providing warranty service. 

This limited warranty does not cover: (1) Defects or damages arising as the result of shipment by common carriers or 
private transportation, unless Folyon undertakes shipment and transportation of the Equipment to Purchaser’s site or 
contractually assumes the risk of damage to the Equipment in shipment; (2) Defects or damages arising out of, or as 
the result, of mishandling, modification, or improper start up, installation or maintenance of the Equipment (including 
start up, installation or maintenance not in accordance with Folyon’s written procedures); (3) Defects or damages 
resulting from, or arising out of, abuse, misuse, neglect, intentional damage, accident, fire, flood, earthquake, or any 
other act of God. 

This warranty as to Equipment is LIMITED to repair or replacement of parts or Equipment in the determination of 
Folyon Technologies Inc. THE FORGOING LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES INCLUDING THE 
IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY. Folyon Technologies Inc. 
DISCLAIMS ANY LIABILITY FOR ANY DAMAGES RESULTING FROM DELAY OR LOSS OF USE IN SERVICE OR REPAIR, OR FOR 
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
OF THE EQUIPMENT, EXCEPT AS STATED IN THIS PARAGRAPH. 

This limited warranty cannot be modified in any way except in writing by both Folyon and Purchaser. Invalidation of 
any one or more of the provisions of this limited warranty shall in no way affect any of the other provisions hereof, 
which remain in full force and effect. 

This limited warranty shall be extended only to the first Purchaser of this Equipment and is not transferable. 

Summary of Contents for H300P

















Reviews:

Related manuals for H300P