manualshive.com logo in svg

Folyon H300P, User Manual

The Folyon H300P User Manual is available for free download from manualshive.com. This comprehensive manual provides step-by-step instructions and in-depth information about operating and maintaining the H300P. Get the most out of your product with this helpful manual, easily accessible and ready for download at manualshive.com.

Share
Download
background image

 

H300P Temperature Humidity Chamber

 

 

Page 14 

 

Troubleshooting  

Symptom 

Causes 

Chamber does not control 
temperature and humidity 

The CONT switch is in the OFF position. 

Humidity does not increases 
fast enough, or does not 
increase above 75%RH 

1.

 

The water in the water reservoir is too low 

2.

 

The water in the water reservoir is too cold.  Allow about 30 minutes 
for the water to warm up to normal operating temperature. 

3.

 

The chamber door is not properly sealed 

4.

 

The water in the reservoir is not distilled. 

Humidity does not decrease 
fast enough 

1.

 

Desiccant is used up (red).  Make sure some of the desiccant in the 
desiccant reservoir is blue. 

2.

 

Condensation in the chamber. 

3.

 

The chamber door is not properly sealed. 

Summary of Contents for H300P

















Reviews:

No comments

Related manuals for H300P

Brands by name

Popular brands

Load more brands