FMI (V)DVF36TCL(-HA) Owner'S Operation And Installation Manual Download

Page: 1 / 36

For more information, visit www.fmiproducts.com

WARNING: If the information in this manual is not fol-

lowed exactly, a fire or explosion may result causing

property damage, personal injury or loss of life.
— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire

department.

— Installation and service must be performed by a quali

fied installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance

CONSUMER: Retain this manual for future reference.

DIRECT-VENT CORNER UNIT FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

NATURAL GAS MODELS

(V)DVF36TCR(E) AND (V)DVF36TCL(E)

(V)DVF36TCR(-HA) AND (V)DVF36TCL(-HA)

PROPANE/LP GAS MODELS

(V)DVF36TCRP(E) AND (V)DVF36TCLP(E)

Right Side Corner

Model Shown

PFS

Summary of Contents for (V)DVF36TCL(-HA)





































Search results

Summary of Contents for (V)DVF36TCL(-HA)

Reviews:

Related manuals for (V)DVF36TCL(-HA)

Brands by name

Popular brands

FMI (V)DVF36TCL(-HA), Owner'S Operation And Installation Manual

Search results

Summary of Contents for (V)DVF36TCL(-HA)

Reviews:

Related manuals for (V)DVF36TCL(-HA)

Brands by name

Popular brands