manualshive.com logo in svg

FLYGT APP 541, User Manual

Share
Download
FLYGT APP 541 User Manual Download Page 33

Phase

Description

3

No more SMS are sent.

RTU tries to sends the SMS to the next recipient.

NOTICE:

If all numbers have been dialled, but no alarm acknowledgement has been received, the
specific alarm will not be sent again.

Function: No alarm acknowledgement time
When the acknowledge request is disabled, SMS alarms are sent to all listed phone
numbers.
Configure SMS alarm acknowledgement

• Specify acknowledgement time in the SMS Acknowledge time menu (15_8).
• To disable acknowledge requests, set acknowledgement time to "0".

Passive Alarms

When alarms become passive, SMS can be sent out.
Specify passive alarm handling

• To send out SMS with passive alarms, select "Yes" in the SMS P-alarm menu (15_9).
• To disable SMS with passive alarms, select "No".

Time Frame for Sending D-alarms

Function: D-alarm time frame
SMS with D-alarms are sent only during a specified time frame. If the alarm occurs at any
other time, the RTU will wait until the D-alarm time frame begins and then send the alarm.
Function: No D-alarm time frame
If the D-alarm time frame is disabled, D-alarms are treated as A-alarms.
Configure time frame

1. Specify when to start sending SMS in the D-alarm start time menu (14_9).
2. Specify when to stop sending SMS in the D-alarm end time menu (14_10).

Disable time frame
Set both start and end times to "0".

Special Alarms

Personnel Alarm

The personnel alarm is used when work of any kind is carried out in a pump station, and
alerts to the risk that an accident may occur.
Before using this function
Configure a General purpose input as personnel alarm input.
Restriction

NOTICE:

The personnel alarm always has alarm priority A and cannot be prevented from being sent.

Function: Personnel alarm

Configure Alarm Handling

APP 541 User manual

31

Summary of Contents for APP 541













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands