manualshive.com logo in svg

Fluke OptiView III Series, Getting Started Manual, Page: 25 / 58

Share
Download
Fluke OptiView III Series Getting Started Manual Download Page 25

19

Workgroup Analyzer

Updating the OptiView Workgroup Analyzer Firmware

anj06f.eps

Figure 7. Remote Management Port Connection

Step Three – Run the User Interface Software

When you launch the user interface software (an icon is placed on your desktop), the analyzer will 
automatically be listed in the OptiView Browser list as long as it is in the local network (broadcast domain). 
Figure 7 shows a WAN connection where you will need to configure the remote PC IP address in the 

Setup | 

Remote

 screen in order to see it in the OptiView Browser.

Note the 

Local Host Software Revision

 number. This number should match the 

Firmware Revision

 numbers 

displayed for each analyzer. If the firmware revision displayed is a lower number than the local host software 
revision number, select that analyzer and click on the update firmware button (right-most on the button 
bar). The software will begin its update process of the firmware on the selected analyzer.

Note

The Connection type has to show “management port” for the update firmware 
button to be enabled. You cannot update the analyzer’s firmware through a network 
measurement interface, only through the Management Port.

Older OptiView Workgroup Analyzers running firmware less than version 5.2 can only 
be updated to firmware version 4.09. A yellow triangle will appear next to analyzers 
less than 4.09 but greater than 3.51 indicating they can be updated to 4.09. OptiView 
Workgroup Analyzers running 3.51 or less firmware can not be updated. 

You cannot update OptiView

TM

 Integrated Network analyzers using this method. See the software update 

procedure for OptiView

TM

 Integrated Network analyzers in the analyzer Help.

Once the user interface software is finished flashing new firmware into your analyzer, the 

Update 

Complete

 dialog box will be presented. Select 

OK

 and continue updating all of the OptiView

TM

 Workgroup 

Analyzers in this manner until all of the firmware revisions match the host software revision number.

W

A

N

Summary of Contents for OptiView III Series



























































Reviews:

No comments