Fluke MOLBOX1 PLUS S - V 6.00, Operation And Maintenance Manual

Page: 124 / 184

™/S, MOLBLOC TERMINAL OPERATION AND MAINTENANCE MANUAL
© 1995 - 2010 Fluke Corporation, DH Instruments Division Page 114
SYNTAX PURPOSE
DEVICE=
Loads information on molbloc connected to into molbox1.
DP Read the differential pressure value being used to calculate flow.
DRV Read or set the status of an external solenoid valve.
ERR Read the last error message.
FA= Start a single flow averaging cycle.
FCOEF Read the coefficient to convert kg/s to the current flow units.
FR Read the next flow measurement.
FRA
Read the results of a completed flow averaging cycle.
FUNIT(=) Read or set the flow display unit.
GAS(=)
Read or set the gas type being used.
GASCAL(=) Read or set the active molbloc calibration to use.
GASCALS List all calibrations available in the active molbloc.
ID (=) Read or set the ID.
KFACT(=) Read or set the “K” factor.
LEAKCK(=) Start a or system leak check cycle or check if a cycle is complete.
LOCAL Enable the front panel controls if in remote and go to local.
MEM Read the memory test status.
MFCCH(=) Read or set the MFC channel and output mode (voltage or current).
MOLBLOC
Read the active molbloc header data. Does not load molbloc information.
OHMS Read the most recent measurement of the active molbloc’s two PRTs.
PCAL
Read or set the user RPT calibrations.
PCALDATE(=) Read or set the user RPT calibration dates.
PCOEF Read the coefficient to convert Pascal to the current pressure units.
PR Read the next molbloc average pressure.
PRHI Read the last measured upstream pressure (tare corrected).
PRLO Read the last measured downstream pressure (tare corrected).
PUNIT(=) Read or set the pressure display unit.
PURGE(=) Read the progress of or start the purge cycle.
RANGE Read the range of the active molbloc.
RATE
Read the next available rate of change of flow.
RE Read the current Reynolds number.
RES(=) Read or set the local flow display resolution.
READYCK(=) Read or set a flag that is cleared by a Not Ready condition.
REMOTE Enable remote local lockout operation.
RESET Reset the settings to the default operating parameters.
SN Read the serial number of the .
SR Read the next available ready status.
SS(=) Read or set the stability required for a Ready <*> condition.
STDRES(=) Read or set the PRT measurement system auto-calibration reference resistor
values.
TARE Read the current tare conditions and the current tare.
TARESETUP(=) Prepares the unit to tare.
TARESET(=) Tare the upstream and downstream RPTs or set tare to a given value.
TCAL (=) Read or set the molbloc temperature calibration (channel dependent).
TEMP Read the current molbloc temperature in the current units.
TIME(=)
Read or set the internal clock’s time.
TOTAL(=) Read the progress of or start a new totalize cycle.
TUNIT(=) Read or set the molbloc temperature unit.
UDU(=) Read or set the user definable pressure unit.
UL(=) Read or set the upper limit for the internal RPTs.
USERCAL(=) Read or set the user flow measurement adjustment.
UTEMP(=) Read or set the temperature reference used for the user flow units.
VALVE This command is obsolete and should not be used in new designs.
VER Read the version.
VLM(=) Read or set the volume units pressure & temperature conditions.
VIN Read the MFC measurement voltage if in voltage mode.
VOUT(=)
Read or set the voltage sent to an external MFC if in voltage mode.
VSENSE Read the voltage sensed at the MFC terminal.
VSUPPLY Read MFC supply voltage.
VVALTEST Read voltage sensed at MFC valve test terminal.
ZOFFSET:HI Read or set the AutoZ pressure offset, (Poffset), for the high RPT .
ZOFFSET:LO Read or set the AutoZ pressure offset, (Poffset), for the low RPT .