background image

FMS-2530 Tabletop Ultrasonic Scaler V.1 

11 

 

Section 12: System Maintenance and Care 

 
Daily Maintenance 
It is recommended that you perform the following 
maintenance procedures to help minimize bio-film 
formation in the water tubing  of your ultrasonic 
scaler which could affect the water flow to the 
ultrasonic insert and scaling performance. 
 
Start-Up Procedures at the beginning of the 
day: 
1. Open the manual shut-off valve on the dental 
office water supply system. 
2. Turn the system ON using the power ON/OFF 
switch. (see illustration on page 7) Verify the power 
indicator light is on. 
3. Set the power control knob to minimum setting. 
4. Set the water control knob to maximum. 
5. Hold the sterilizable sleeve of the  handpiece 
(without an insert installed) upright over a sink or 
drain. Activate the foot control and flush the water 
line for at least 2 minutes. 
6. Place a sterilized insert into the sterilizable sleeve 
of the handpiece and set the water control knob to 
your preferred operating position. 
 
Between Patients: 
1.

 

Remove  the  ultrasonic insert and sterilizable 
sleeve of the handpiece used, clean and sterilize. 

2.

 

Clean and disinfect the surfaces of the cabinet, 
power cord, Flight handpiece cable set assembly*, 
control knobs, foot pedal and Flight  handpiece 
cable set assembly by applying an approved 
non-immersion type disinfectant solution* 
carefully following the instructions provided by 
the disinfectant solution manufacturer. To clean 
system, generously spray disinfectant solution on 
a clean towel and wipe all surfaces. Discard used 
towel. To disinfect system, generously spray 
disinfectant on a clean towel and wipe all surfaces. 
Allow disinfectant solution to air dry. Do not spray 
disinfectant solution directly on the ultrasonic 
scaler. 

3.

 

Place a sterilized handpiece  sleeve on the 
handpiece cable. Set power to minimum. Hold the 
handpiece sleeve over a sink or drain and flush 
the water line at maximum water flow for 30 
seconds. 

4.

 

When ready, place a sterilized insert into the 
handpiece sleeve. 

5.

 

Please consider using an FDA approved sheath for 
the cable and entire handpiece or at least cover 
the handpiece from the fastening ring to the cable 
when the sleeve is sterilized between patients. 
 

*Note: If the power intensity adjustment knob is 
set to minimum, you might not activate the system 
enough and get no water flow or no vibration.   In 
that case, please set the power intensity adjustment 
knob to the middle, then activate the foot control 
and then turn the power intensity adjustment knob 
to your preferred setting. 
 
Shut-Down Procedures at the end of the day: 
1.  Remove  the  ultrasonic insert and sterilizable 
sleeve of the handpiece used. Clean and sterilize. 
2.

 

Turn the system OFF. 

3.

 

Clean and disinfect the surfaces of the case, 
power  cord, Handpiece cable set assembly, 
control knobs, foot pedal and cable set assembly 
by applying an approved non-immersion type 
disinfectant solution* carefully following the 
instructions provided by the disinfectant solution 
manufacturer. To clean the  system, generously 
spray disinfectant solution on a clean towel and 
wipe all surfaces. Discard used towel. To disinfect 
the  system, generously spray disinfectant on a 
clean towel and wipe all surfaces. Allow 
disinfectant solution to air dry. Do not  spray 
disinfectant solution directly on the ultrasonic 
scaler. 

4.

 

Close the manual shut-off valve on the dental 
water supply system. 

Summary of Contents for FMS-2530



















Reviews: