Fitnation Flex Bike Ultra Page 9 Instruction Manual Download | Manualshive

Page: 9 / 24

background image

9

ASSEMBLY INSTRUCTIONS

Tighten nut onto screw with

included wrench. Repeat on other

side.

Place the nuts and washers to the

side for now.

Place the washers over the

screws from seat cushion.

Take nuts and washers off of the

seat cushion.

Fit seat post onto seat cushion

screws.

Finger tighten each nut onto

the screws from seat cushion.

If difficult to tighten, nut may be

upside-down.

«
...
7
8
9
10
11
...
»

Summary of Contents for Flex Bike Ultra

























Reviews:

No comments

Related manuals for Flex Bike Ultra

Brand: Hagie Pages: 61

Brand: JackJaw Pages: 2

Litmann Quality 3100

Brand: 3M Pages: 2

Brand: Cambridge Audio Pages: 2

Brand: Quanser Pages: 12

Brand: Olsen Pages: 4

Dominator Series

Brand: Falcon Pages: 31

Brand: Fakir Pages: 22

Brand: Xtool Pages: 51

Brand: H-TEC Education Pages: 16

Brand: H-TEC Education Pages: 12

Brand: YOKOGAWA Pages: 75

Brand: Fagor Pages: 12

Brand: Baltic Pages: 68

Brand: H&S Pages: 76

MCX-C15 - MusicCAST Network Audio Player

Brand: Yamaha Pages: 114

Brand: Daihan Scientific Pages: 27

WEEDDEVIL ST-97

Brand: R+M Suttner Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands