Fitnation Flex Bike Ultra Page 12 Instruction Manual Download | Manualshive

Page: 12 / 24

background image

12

ASSEMBLY INSTRUCTIONS

Align the seat handles with holes on

the bottom of the backrest support.

Tighten down screws with included

large hex key/screwdriver tool.

Align backrest against backrest

support. Insert screws and finger

tighten (see parts diagram).

Place screws into holes and

finger tighten.

Tighten down screws with included

large hex key/screwdriver tool.

Screw adjustment knob into

backrest support.

«
...
10
11
12
13
14
...
»

Summary of Contents for Flex Bike Ultra

























Reviews:

No comments

Related manuals for Flex Bike Ultra

Brand: Oberheim Pages: 40

Brand: Fisher Scientific Pages: 42

Brand: Nautilus Pages: 17

Brand: National Instruments Pages: 6

ThermoTweez Handpiece TT-65

Brand: Pace Pages: 14

Brand: T&D Pages: 28

ULTRATHERM 908i

Brand: gbo Pages: 32

Brand: Dantel Pages: 6

Brand: Zero 88 Pages: 22

Brand: Yaasa Pages: 20

TOTAL KNEE 1900

Brand: Össur Pages: 58

Pro hunter 2525

Brand: SprotDog Pages: 28

Brand: Ocean Signal Pages: 2

RadioPRO 4 RP4-MZ11

Brand: PAC Pages: 5

Brand: Wacker Neuson Pages: 42

Brand: KERR Pages: 32

Brand: Zahl Pages: 34

Brand: Hydrofarm Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands