Fitnation Flex Bike Ultra Page 10 Instruction Manual Download | Manualshive

Page: 10 / 24

background image

10

ASSEMBLY INSTRUCTIONS

Tighten nut onto screw with

included wrench. Repeat on

other two nuts.

Insert seat post into main frame.

Remove screw, nut, and washer

from the backrest support.

Loosen triangular knob and

remove from the main frame.

Secure knob back into place at

desired height.

Place the screw, nut, and washer

to the side for now.

«
...
8
9
10
11
12
...
»

Summary of Contents for Flex Bike Ultra

























Reviews:

No comments

Related manuals for Flex Bike Ultra

Giraffe OmniBed

Brand: Ohmeda Pages: 54

Brand: DBX Bushido Pages: 12

PowerXL DX-NET-ETHERNET2-2

Brand: Eaton Pages: 48

Power Xpert C445

Brand: Eaton Pages: 2

Brand: Farmi Forest Corporation Pages: 32

Brand: Harken Pages: 4

Brand: Harken Pages: 2

TERRA FORCE BOOM

Brand: Hardi Pages: 40

Brand: Harken Pages: 4

QuickSlide HemaPRO

Brand: Hardy Diagnostics Pages: 2

Brand: Hardt Pages: 2

Brand: JB-Lighting Pages: 32

Brand: W&H Pages: 72

Brand: YMC Pages: 49

Brand: Octane Fitness Pages: 8

Brand: Octane Fitness Pages: 10

Brand: OCENCO Pages: 48

Brand: Ocean Optics Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands