background image

Testing The DAS Sensor

STEP 1: 

Turn the ignition off and Arm/Lock the system. 

STEP 2: 

Wait 30 seconds then test the impact sensitivity.

FT-EZGO Setup

The FT-EZGO from Firstech will unlock/disarm the vehicle when in range. It is capable of proximity lock/arm 
and unlock/disarm when in or out of range off the vehicle. There is a manual override button located on 
the back of the EZ-GO remote. It will lock/arm, unlock/disarm by press and releasing the button for ½ of 
a second (0.5 seconds). It will also trigger the trunk release output by press and releasing the button for ½ 
second (0.5 seconds) then holding for 2.5 seconds.

Installing The FT-EZGO
STEP 1: 

Set Option 1-14 to Setting 2, 3 or 4

 

STEP 2:

 Connect included Blue 6 Pin (With Ground Wire) to Black 6 Pin to control module. If connecting 

to a 4 Pin to 4 Pin antenna, use the included 6 Pin to 4 Pin adapter.

STEP 3:

 Connect the ground wire from the included 6 Pin to 6 Pin cable to vehicle’s ground. 

Warning: 

Failure to connect this wire WILL result in damage to your FT-EZGO antenna (ANT-
RFID).

STEP 4:

 If you are using an additional RF kit the antenna cable will connect to the blue 6 pin connector 

on the EZ-GO antenna either directly or using the 6 to 4 pin adapter harness included with the 
EZ-GO kit.

 

STEP 5:

 Find a spot to mount your ANT-RFID on the windshield. This is recommended for optimum 

range. For more specific mounting location information visit us at techfeed.compustar.com 
under the Authorized Tech section document titled: “FT-EZGO Recommended Mounting 
Locations.” 

STEP 6:

 Program your EZ100-R using the standard remote programming procedure along with any 

additional RF Kit remotes to the control module (Maximum 4 Remotes including EZ100-R). You 
are now ready to test your FT-EZGO system.

Testing The FT-EZGO
STEP 1:

 Turn the proximity lock/unlock feature on by holding the button on the EZ100-R for 8-10 

seconds. You will get one parking light flash and/or siren chirp. To deactivate the proximity 
feature simply hold the button again for 8-10 seconds and you will get two parking light flashes 
and/or chirps to indicate your feature is off.

Copyright 2014 Firstech, LLC.

Page 3

Copyright 2014 Firstech, LLC.

Page 3

Copyright 2014 Firstech, LLC.

Page 11

CM7200

 

Master Guide

Starter System

techfeed.compustar.com

Summary of Contents for CM7200
























































Reviews: