background image

9

®

2.

Press the MODE key and the screen displays PROGRAMMER EP113

3.

Press the SCRL key until the screen displays UNIT ADDRESS #00 (or appropriate address).

4.

Every time the RESET key is held down for 1 second and then released will increase the address
by one.

5.

Maximum address is 15. Then the address will roll over to 00.

Method Two

1.

Make sure the control is not in a lockout condition. If so, pressing the reset button will reset the
lockout condition and then proceed.

2.

Open the operating control (term L1-3).

3.

Move the “Check-Run” switch to the Check position.

4.

The display will indicate Unit Address 00 (or the current address).

5.

Every time the reset button is held down for 1 second and then released will increase the address
by one.

6.

Maximum address is 15. Then the address will roll over to 00.

OPERATION

The Fireye Flame-Monitor control provides proper burner sequencing and flame monitoring on auto-
matic burners. It also provides the operator a status readout as well as diagnostic information. It has a
number of unique messages which are simple to understand and interpret. These messages are, at
option, in English, French, Dutch, Spanish or German.

Description of Interlocks

1.

The opening of any interlock in the L1-3 circuit will stop the burner without causing lockout or
alarm. When the interlocks are closed, the burner start sequence is initiated. These interlocks
include the thermostat switch, which is closed when heat is required.

2.

Running interlocks (3-P): If any interlock switch in this circuit opens, all open fuel valves will be
closed immediately and the control will go in alarm or lockout (non-recycle operation). The con-
trol must then be manually reset. These interlocks include for instance the air flow switch.

Note: Dipswitch #1 on the EP113 programmer provides the option to recycle the control instead of
going into alarm. See “Dipswitches for Selectable Operation.”

3.

High fire or purge interlock (D-8):. This is the firing rate motor linkage position switch or a dif-
ferential air pressure switch that proves a maximum purge air flow rate.

4.

Low fire start interlock (M-D): This is the firing rate motor linkage position switch or a damper
position switch, which will prove both the linkage and damper are in their proper positions to
begin burner light off.

START-UP PROGRAM

The E210/211 with ED510 display module, programmer module, flame amplifier module, and the
appropriate flame detector, provides the following burner operation sequence.

1.

With power applied the blower motor is energized through terminal M when the following condi-
tions are met: 

— Recycling limits (demand for heat) are closed. 

— The air flow switch is open at start or opens within 30 sec.

*

— No lockout 

The air flow switch closes. The other running interlocks (depending on fuel selection) also close (all
within 30 sec.).

2.

The firing rate motor is driven to the high fire position.

*  

Dipswitch #6 enables or disables this requirement, See “Dipswitches for Selectable Operation”

Summary of Contents for FLAME-MONITOR E210

































Reviews: