background image

INITIAL START-UP OPERATION

  1.  Place circuit breaker in ON position.  The pump may start immediately if system pressure is low.  

The PUMP RUNNING and LOW PRESSURE LED’s will be lit.

2.  If the Mark IIXG is con

fi

 gured for automatic shutdown (AUTOMATIC STOP enabled), the pump 

motor will continue to run for the period of time set in the MIN RUN (or OFF DELAY) screen and 
then stop automatically, providing the STOP pressure setting has been reached.  Both the system 
pressure and MIN RUN (or OFF DELAY) time remaining will be shown on the display.  Depressing 
the STOP push-button during the running period will stop the motor as long as the button is held 
in.  However, the motor will restart when the button is released if system pressure is below the 
stop setting.

  3.  If the controller is con

fi

 gured for manual shutdown (AUTOMATIC STOP disabled), the pump 

 

will continue to run until the STOP push-button is depressed.

  4.  To stop the motor otherwise, press and hold the STOP push-button and place the CIRCUIT BREAKER 

DISCONNECTING MEANS handle in the OFF position.

FOR MANUAL START

  1.  Follow the initial start-up instructions.  The isolating switch/circuit breaker should be closed, the 

POWER AVAILABLE LED should be illuminated and system pressure normal, i.e. higher than the 
programmed START PRESSURE setting.

  2.  Press the START push-button.  The pump motor should start and continue to run.  It will  not    
 

stop automatically.  The running period timer and pressure switch have no control over this manual 
operation.

  3.  To stop, press the STOP push-button.
  4.  Starting from a remote START push-button (if used) functions in the same way as the local START 

push-button.

  5.  If the pump motor restarts, system pressure is below the START PRESSURE setting.

FOR EMERGENCY RUN START

  1.  Put the circuit breaker/isolating switch in the “off” position.
  2.  Push and lock the EMERGENCY RUN handle.  Place the circuit breaker/isolating switch handle in 

the “on” position.  The motor will start and continue to run until both of the following conditions 
have been satis

fi

 ed:

 

a.  The EMERGENCY RUN handle has been turned to “unlock” position and released.

 

b.  The STOP push-button is pushed.

  3.  To stop the motor with the handle locked in the “run” position, place the circuit breaker  handle 

in the OFF position, then turn the EMERGENCY RUN handle and release.

  4.  Return the circuit breaker operator to the ON position.
  5.  If the pump restarts, system pressure is below the START PRESSURE setting.

ABBREVIATED STARTING SEQUENCE

FTA750, FTA1000, 2000 FULL VOLTAGE CONTROLLER
  1. Follow all of the initial start-up instructions.
  2. The motor will start and run at full line voltage.

FTA1250 PART WINDING CONTROLLERS
  1.  Follow all of the initial start-up instructions.
  2.  MOTOR ACCELERATION timer is factory set for 2 seconds and may be 

fi

 eld adjusted if necessary.  

(See 

Mark IIXG Programming

 for details).

CAUTION:  DO NOT EXCEED FOUR (4) SECONDS MAXIMUM OR MOTOR MANUFACTURER’S LIMITS.

7

Summary of Contents for Emerson Mark IIXG




























Reviews: