manualshive.com logo in svg

Firemiks 1200-3-PP-F-ALU-FM, Instruction Manual

Share
Download
Firemiks 1200-3-PP-F-ALU-FM Instruction Manual Download Page 43

Page 43/43 

 
 
 
 

 

 

 

 

Firemiks AB 

Instruction manual version: SPFA FM 

P.O. Box 8155, 104 20 STOCKHOLM, Sweden 

  

phone +46-8-551 196 10 - [email protected] - www.firemiks.com 

(5.2.3) 

NOTE! 

Make sure that the cover over the drive shaft and the protection 

cap on the back gable side are in place.

 

 

(6)   

Operation 

 

(6.1.2) 

Read the warnings on page 26

 

 
(6.6.1) 

Some units are equipped with an optional dosing return valve. This valve 

is not to be used during regular operation and it should remain with the valve 
positioned for dosing into the main water line only. The valve should only be 
operated by qualified maintenance personnel for maintenance/testing purposes. 
See 4.8 for more information.

 

 

(7)   

Maintenance 

 

(7.2) 

WARNING! It is extremely important that at every service or maintenance 

of the unit you must assure yourself that the unit cannot be started by mistake.

 

(7.2.1) 

Close completely a shut-off valve in the main water supply before the unit 

and make sure it cannot be opened while you are working on the unit, see 
also 4.3.9.  

Note also WARNING SIGNS on the unit.

 

 

(8)   Troubleshooting 
 

(8.2) 

NOTE! There is a risk for powerful jet streams of water at leakages when 

the system is under pressure. Be sure to make the unit (and if necessary the 
system) without pressure when doing service.

 

 
 

 
 
 
 

FIREMIKS® is a registered trademark owned by Firemiks AB. 

 

We reserve the right to make changes in the specifications without prior 
notice.  

Summary of Contents for 1200-3-PP-F-ALU-FM












































Reviews:

No comments

Brands by name

Popular brands

Load more brands