manualshive.com logo in svg

Firemiks 1200-3-PP-F-ALU-FM, Instruction Manual

Share
Download
Firemiks 1200-3-PP-F-ALU-FM Instruction Manual Download Page 4

Page 4/43 

 
 
 
 

 

 

 

 

Firemiks AB 

Instruction manual version: SPFA FM 

P.O. Box 8155, 104 20 STOCKHOLM, Sweden 

  

phone +46-8-551 196 10 - [email protected] - www.firemiks.com 

2  Read this first! 

2.1  Check at the reception of the goods that the delivery is complete 

and without damages. Any discrepancies and damages should be 
informed to the transport company and the supplier immediately. 

2.2  For your own safety it is very important that you read all 

information in this Instruction Manual before you install and use 
this equipment, especially the comprehensive section 12 Overview 
and repetition of procedures essential for safety. We want to point 
out that the user is responsible that the safety instructions are 
followed strictly. See also the WARNING SIGNS on the unit. 

2.3  The FIREMIKS unit must be assembled and installed by qualified 

staff, with the necessary mechanical and technical skills, following 
the user and safety instructions given in this manual. As the user, 
you are responsible that the safety and operating instructions of 
any other systems, environment or container where the FIREMIKS 
unit is installed are followed.  

2.4  Inform yourself about the fire-fighting concentrate (additive) 

producer's instructions about leakages and spillage. Observe 
especially the directions about spillage on hands and eyes. Assure 
yourself also that local and national regulations are followed 
concerning environmental protections regarding waste leakage, 
spillage and tests with the fire-fighting liquid. 

2.5  The unit must only be used under the working conditions specified 

in this instruction. Any deviation from that requires the producer's 
permission. 

2.6  The user is responsible to carry out the instructions according to 

chapter 7 Maintenance. 

2.7  The unit is designed to dose fire-fighting liquids (=concentrate) in 

fire-fighting main water line. The FIREMIKS is designed to serve in 
fire emergencies. It is not suitable for continuous use. For all other 
applications, contact must be made with Firemiks AB for an 
approval, if possible to give such.  

 

 

Summary of Contents for 1200-3-PP-F-ALU-FM












































Reviews:

No comments

Brands by name

Popular brands

Load more brands