manualshive.com logo in svg

Firemiks 1200-3-PP-F-ALU-FM, Instruction Manual

Share
Download
Firemiks 1200-3-PP-F-ALU-FM Instruction Manual Download Page 42

Page 42/43 

 
 
 
 

 

 

 

 

Firemiks AB 

Instruction manual version: SPFA FM 

P.O. Box 8155, 104 20 STOCKHOLM, Sweden 

  

phone +46-8-551 196 10 - [email protected] - www.firemiks.com 

12  Overview and repetition of paragraphs essential for safety 

 

(2)  

Read this first!

 

 

 

The whole section 2 is important to read! 
 

(4)   

Installation 

 

(4.2.1) 

For weight see Appendix 1, Data sheet. Suitable points to lift the unit are 

shown in Appendix 2, Dimensional Drawing. The 3200 unit also has holes for 
lifting eyes shown on the Dimensional Drawing. The unit should not be exposed 
to strokes or knocks.

 

 
DO NOT LIFT THE UNIT USING THE PIPING 
 

(4.6.10) 

Make sure there is enough space around the unit to enable easy access 

for service and maintenance, especially on the back gable side of the water 
motor (opposite side of the concentrate pump).

  

 

(4.8.1) 

Some units are equipped with an optional dosing return valve

, also DRV 

in short. This valve is not to be used during regular operation and its 
handle should remain positioned for dosing into the main water line only. 
The valve should only be operated by qualified maintenance personnel for 
maintenance/testing purposes.

 

 
(4.3.1) 

FIREMIKS is designed to operate with clean water

. Water must be 

free from sand, gravel and other debris that may wear out the volumetric water 
motor quickly. In most cases the FIREMIKS can cope with occasional instances 
of isolated foreign objects up to 2 mm size. If there is an acute risk of particles 
entering the FIREMIKS or when polluted or contaminated water is used, the 
piping system must be designed so that there is a suitable filter or strainer where 
this pollution can be collected 

fully

, placed 

before

 (upstream of) the FIREMIKS. 

We refuse any responsibility for blockage or damage of the water motor by 
any foreign objects in the water, whatever their size.

 Please contact us if you 

need further guidance in this subject.

 

 
(4.3.9) 

Note! It is extremely important that a shut-off valve is installed 

before the FIREMIKS unit.

 This is to ensure a risk-free service/maintenance, i.e. 

the risk for sudden rotation of the water motor due to unexpected water flow will 
be eliminated by closing this valve. When working on the FIREMIKS, put a clear 
sign on this valve stating: 

“Do not open, maintenance work in progress”.

  

 
(4.3.11) 

Note! As in all safety-related installations, there should always be a 

back-up plan

. Never design the installation in such a way so that the water flow 

through the FIREMIKS is the only source for fire-fighting water.

 

 

(4.10.1) 

Note! Never let the FIREMIKS run dry without concentrate or 

flushing water

. See 6.4.1 for more info.

 

 

(5)  

Check before first start 

 

Summary of Contents for 1200-3-PP-F-ALU-FM












































Reviews:

No comments

Brands by name

Popular brands

Load more brands