manualshive.com logo in svg

Firemiks 1200-3-PP-F-ALU-FM, Instruction Manual

Share
Download
Firemiks 1200-3-PP-F-ALU-FM Instruction Manual Download Page 29

Page 29/43 

 
 
 
 

 

 

 

 

Firemiks AB 

Instruction manual version: SPFA FM 

P.O. Box 8155, 104 20 STOCKHOLM, Sweden 

  

phone +46-8-551 196 10 - [email protected] - www.firemiks.com 

 

6.4  Note! Never let the FIREMIKS run dry without concentrate or 

flushing water, this will damage the concentrate pump. 

6.4.1 

The concentrate pumps can withstand some dry running without damage for 
a limited time. Dry running must however never be purposely chosen or relied 
upon.

 

6.4.2  When all concentrate liquid is finished, quickly switch to Flushing with 

the Selector valve Dosing / Flushing on the concentrate pump inlet (No. 
4 on Flow Chart). Or stop the FIREMIKS altogether by shutting down the 
main water flow. 

 

6.5  After operation in a fire: 

6.5.1  After use of the unit in a fire, or in a test with large water flows; check the 

function according to paragraph 7.5.2 

6.5.2  Preventive maintenance measure: when the unit has served in a major fire 

and the operator wants to ensure optimum future functioning, it may be 
appropriate to change the Vanes in the unit. Contact your distributor or 
Firemiks AB for spare parts and instructions.  

 

6.6  Optional Dosing Return Valve. 

6.6.1  Some units are equipped with an optional dosing return valve. This valve is 

not to be used during regular operation and it should remain with the valve 
positioned for dosing into the main water line only. The valve should only be 
operated by qualified maintenance personnel for maintenance/testing 
purposes. See 4.8 for more information.  

 

6.7  Salt sea water use 

 
The Firemiks may be operated with salt water.  
 
FIREMIKS with the aluminum water motor 

must always be flushed with fresh 

water after use. 

This is to avoid excessive corrosion of the aluminum housing. 

The surface treatment has good resistance to corrosion, however with use 
scratches into the coating may corrode after prolonged exposure to salt water 
and impair correct functioning of the unit.  
 
Also if not flushed with fresh water, crystallizing salt will impair the correct 
function of the water motor and the concentrate pump.  
 
FIREMIKS with the 

nickel-aluminum bronze and stainless-steel

 water motor 

must always be flushed with fresh water if the unit is drained after use. 

Otherwise, crystallizing salt deposits can possibly impair the correct function of 
the water motor and the concentrate pump.  

Summary of Contents for 1200-3-PP-F-ALU-FM












































Reviews:

No comments

Brands by name

Popular brands

Load more brands