background image

FireClass Fire detection system  FireClass Panels

5.4 Psuedo Points In FireClass

Service and Maintenance  Doc. version 1

29

5.4.2

Point Section – RBUS Node Faults

When reported on the user interface or via printers, the out-
put format used for faults reported from an RBus node faults 
are:
‘RBnn’ : where nn is the node number 0 - 15.

5.4.3

Point Section – Network Card 
Faults

When reported on the user interface or via printers, the out-
put format used for faults reported from Network Card Fault 
points are:
‘TLI Pnn’ 
where nn is the point number 01-11

5.4.4

Point Section – COM1 Faults

When reported on the user interface or via printers, the out-
put format used for faults reported from COM1 are:
‘COM1’ 

Complete Nodes-Faults

This section refers to faults regarding presence 
or absence of complete nodes, It is NOT an indi-
cation of faults held by the node but the node 
itself.
This set of points are exceptions to the normal 
address where the first point address is ‘One’ 
instead here as the RBUS units can be 
addressed from 0-15 the first address is ‘Zero’

Field

Description

Address

Pseudo Point 0 - 15

Label

RBUS Fault

Use

Used by RBUS / COMMS 
driver to indicate loss of 

 

configured nodes / presence 
of un-configured nodes-
firmware incompatibility 
issues.

Table 31: Psuedo Point 0-15-Details

Network Cards-Faults

This section refers to faults assigned to the 

 

network card. The configuration is controlled by 
the use of the options in the ‘Network Card’ dia-
log within FireClass Express.
Points 1 to 8 are used for TLI800 card

Field

Description

Address

Pseudo Point 1 – 99

Label

Network Node

Use

Used by supervisor panel to 
indicate which panels are not 
responding to supervision or 
if being supervised reporting 
lack of supervision.

Table 32: Psuedo Point 1-99-Details

COM1-Faults

This section refers a fault regarding presence of 
absence of a printer connected to COM1.

Field

Description

Address

Pseudo Point 1

Label

Printer Comms

Use

If a printer is configured and is 
not connected to the panel 
then this monitor point will be 
activated.

Summary of Contents for FC-P-S







































Reviews: