Document #51073 Rev. A 1/19/99 P/N 51073:A
35
Program Mode
Primary Central Station Number Communication Format (20)
One location is needed to select the Communication Format to the primary phone number. Address 20 is used for
this purpose. The factory default setting for this address is 'E', which is Contact ID Format. You may enter '0'
through 'D' in place of the default, then press [ENTER/STORE]. Choose from the list of formats below:
0: 4+1 Ademco Express Standard, DTMF, 1400/2300 ACK
1: 4+2 Ademco Express Standard, DTMF, 1400/2300 ACK
2: 3+1 Standard 1800 Hz Carrier, 2300 Hz ACK
3: 3+1 Expanded 1800 Hz Carrier, 2300 Hz ACK
4: 3+1 Standard 1900 Hz Carrier, 1400 Hz ACK
5: 3+1 Expanded 1900 Hz Carrier, 1400 Hz ACK
6: 4+1 Standard 1800 Hz Carrier, 2300 Hz ACK
7: 4+1 Expanded 1800 Hz Carrier, 2300 Hz ACK
8: 4+1 Standard 1900 Hz Carrier, 1400 Hz ACK
9: 4+1 Expanded 1900 Hz Carrier, 1400 Hz ACK
A: 4+2 Standard 1800 Hz Carrier, 2300 Hz ACK
B: 4+2 Expanded 1800 Hz Carrier, 2300 Hz ACK
C: 4+2 Standard 1900 Hz Carrier, 1400 Hz ACK
D: 4+2 Expanded 1900 Hz Carrier, 1400 Hz ACK
E: Contact ID, DTMF, 1400/2300 ACK
F: Future use
Consult the Central Station for proper Format selection. For any Format chosen, all event codes are automatically
programmed by the 411UDAC. Refer to Table 3-2, “4+2 Standard and 4+2 Express Formats - Primary,” on page
37, Table 3-3, “A ll 3+1, 4+1 and 4+2 Expanded Formats - Primary,” on page 38 and Table 3-1, “A demco Contact
ID Format - Primary,” on page 36.
Event Codes - Setting Entries
The Format selected in address 20 will cause the 411UDAC to automatically program addresses 145 - 228 with the
factory default settings. Any of the Event Code settings may be altered. Consult your Central Station prior to altering
the event code settings. An entry of all zeros for any event code will cause the communicator to NOT transmit the
report. Note that default event codes for process monitoring are zeroes, preventing the transmission of a process
monitoring event to the Central Station. Transmission of reports to either or both Central Station phone numbers may
be disabled.
Note that default event codes for process monitoring are zeroes, which prevent a Central Station call upon a process
monitoring event. Refer to “Events and Default Event Codes” on page 78, for a further explanation of event codes.
Upon accessing the first event code address (address 145) shown in Table 3-2 , the following may be displayed on the
Programmer 7-Segment Display, if the corresponding Format was selected in address 20.
The first three locations on the left of the Programmer display represent the memory address 145 of the Format previ-
ously selected in address 20. The last location 1 (farthest right) represents the contents of memory address 145
(which is the first digit of the event code).
The following Tables list the data which is automatically programmed for each Format that can be selected in address
20. The addresses shown in each Table contain the Setting data which is automatically programmed by the
411UDAC. To change the value, key in the new digit and then press the [ENTER/STORE] key to save the new
value. Use the Up and Down Arrow keys to increment to the next address or decrement to the previous address.
1451
(address)(data)
Summary of Contents for Fire-Watch 411UDAC
Page 18: ...Mounting 18 Document 51073 Rev A 1 19 99 P N 51073 A FIGURE 2 3 411UDAC Backbox 411ACABB CDR ...
Page 80: ...80 Document 51073 Rev A 1 19 99 P N 51073 A Notes ...
Page 82: ...82 Document 51073 Rev A 1 19 99 P N 51073 A Notes ...
Page 83: ...Document 51073 Rev A 1 19 99 P N 51073 A 83 Notes ...
