Filtreco 100300, User Manual

Page: 13 / 16

13 www.filtreco.nl
• Complete cleaning:
- Switch off the "Main switch" and unplug the system from
the mains power supply.
- Close the inlet and outlet spouts and drain the water
through the valve until the filter is empty.
- Remove the drain and clean it thoroughly.
- Remove the drum and brushes and clean them
under running water.
- Remove the spray pump and clean it
thoroughly.
- Clean the entire inside of the filter.
• disassemble the drum as follows:
- Disassemble the spray tube by unscrewing the
connector and removing the drain from the tube clamp.
- Disassemble the drain by loosening the bolts.
Be careful not to lose the gasket and gasket rings!
- Turn the drum until the bolt from the shaft connection
is on top. Remove this bolt.
- Slide the drum slightly towards the partition until the
tube is separated from the shaft and then carefully lift
the drum at an angle upwards out of the silicone seal. Lift
the drum out of the filter basin. Carefully set the drum
down to prevent damage to the screen.
• Assemble the drum as follows:
- Carefully lower the drum into the filter and set its flange
on the shafts of the partition.
- Press the silicone seal into the flange of the drum on
all sides, using your hand.
- Slide the drum with the flange side over the shaft.
- Turn the drum around the shaft until the hole in the shaft
is positioned underneath the hole in the tube. Reinsert
the M8 x 15 bolt and screw it tightly.
11. Troubleshooting
Error codes related to the Error LED are found in chapter 9.
The following issues may occur:
• No water flow:
- Check whether the (slide) valves are open.
- Check whether the water pumps are connected.
- Check whether the inlet or outlet is clogged.
• Insufficient water flow:
- Check whether the inlet or outlet is clogged.
- There are not enough inlet connections installed.
- The circulation pump does not have enough capacity.
- There is dirty water and particles in the clean water side
outside the drum: check the seal between the partition
and the flange of the drum.
• The high-pressure pump does not work:
- The plug is not plugged into the right power socket (spray
pump).
12. Winterising
To ensure proper functioning of the system, do not allow the
water temperature to decrease below +4 degrees Celsius.
Measures that you can take:
• Place a cover or lid over the drain.
• The control and motor cannot withstand freezing tempera-
tures. Be sure to place them in a location that is protected
from rain and frost.
In case water temperatures drop below +4 degrees Celsius or
there is a chance of freezing, discontinue using the system.
• Drain the system and clean it according to the instructions
• Allow the surrounding pipes to drain
• Leave the valves open
• Protect the pipes and other components from frost if
necessary.
13. Wear parts
The following parts may be subject to wear:
• Silicone drum seal Order number 100754
• Retaining ring Order number 100757
• Brush Order number 100758
• Drum screens Order number 100701
14. Technical specifications
• Operating voltage: Vac 230V
• Plug: 16 A Euro plug
• Total power output: 3680 Watts
• Cable length: 3 m
• Drum diameter: 40 cm
• Drum length: 40 cm
• Max. flow: 35 m
3
/h
• Weight: 55 kg
• Height above water level: 165 mm
• Min. water level: 30 mm below the line
of the arrow
• Max. water level: 10 mm above the line
of the arrow
• Number of panels: 2
• Number of sprayers: 4
15. Wiring and power outages
If the control box is further away than the 3-metre cable length,
use a CE-approved splash-resistant extension cable to reach
the motor and the spray pump. The cables for the water level
meter cannot be extended using a power cable. This may cause
the system to malfunction. Original Filtreco cables can be ordered
separately. Any damage to the control box caused by your own
wiring or third-party extension cables is not covered by warranty.
If following a power outage, the power circuit it reactivated, the
control box will revert to its previous mode (the mode which
was activated for longer than 10 seconds): automatic mode in
automatic mode and manual mode in manual mode. The
previously selected flush time will also be reactivated.