manualshive.com logo in svg

Fike TWINFLEX SRP 100-0001, Engineering And Commissioning Manual

Share
Download
Fike TWINFLEX SRP 100-0001 Engineering And Commissioning Manual Download Page 57

TWINFLEX

®

 SRP Control Panel Engineering and Commissioning Manual 

 

57 

 

 
This allows the selection of subscreens that will allow setting the Type 
and Behaviour of the outputs. 
 
 
 
 

 
 

 

 
This will allow the engineer to view or change the operation of 
Monitored Output. Use the 

LEFT

 and 

RIGHT

 arrow keys to move the 

cursor to a different option and the 

UP

 and 

DOWN

 arrow keys to 

change the current value. To confirm the changes press 

ENTER

.  

 

TYPE:  

Notification 

– sets the type to a notification device (strobe or sounder) 

Release 

– sets the output to a releasing type to allow activating a 

solenoid device. 

 
 

 

 

This will allow the engineer to view or change the operation of 
Monitored Output Use the 

LEFT

 and 

RIGHT

 arrow keys to move the 

cursor to a different option and the 

UP

 and 

DOWN

 arrow keys to 

change the current value. To confirm the changes press 

ENTER

.  

 
 

 

SILENCABLE: 

Yes 

–  

Pressing the silence alarms button will silence the output. 

No 

– 

Pressing the silence alarms button will not silence the output. 

 
STATE:

 

OFF - 

Output is turned off 

Alarm 

–  

Output will activate when the panel in is in the Fire 1(Alarm) state or Sound 
Alarms input/button is activated.  

Pre-Release 

– 

Output will activate when panel is in the Fire 2(Pre-Release) state 

Release- 

Output will activate when panel is in the Release state 

 

PATTERN: 

Continuous 

– 

The output will operate in a continuous (constant) pattern when activated. 

Slow 

– 

The output will operate with a slow (1/2 second on, 1/2 second off) pattern when 
activated. 

Fast 

– 

The output will operate with a fast (1/4 second on, 1/4 second off) pattern when 
activated. 

Temporal 

– 

The output will operate with a temporal pattern when activated. 

User 1-4 -  

The output will operate with a user defined pattern when activated. (The user 
patterns can only be defined in OSP software) 

 

 

 

 

 
IMPORTANT NOTE:  If the Behaviour of the monitored output is configured and then the Type is changed from 
Notification to Releasing or vice versa the panel clears out the Behaviour to default setting.   
Default Behaviour is OFF State, Continuous Pattern and Silenceable Output. 

 

11. Panel I/O 

2. MONITORED OUTPUTS 

11. Panel I/O 

1 Type screen 

11. Panel I/O 

2 Behaviour screen 

OUTPUT: 01   
STATE: Off 

PATTERN: Continuous 

SILENCABLE: Yes 

 

OUTPUT OPTIONS 

1 Type 
2 

Behaviour

 

 

OUTPUT: 01   
TYPE: Notification 
NAME: OUTPUT_01 

↑/↓ /

 

→ /← /

Enter

/

Esc 

 

Summary of Contents for TWINFLEX SRP 100-0001















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands