manualshive.com logo in svg

Fike TWINFLEX SRP 100-0001, Engineering And Commissioning Manual

Share
Download
Fike TWINFLEX SRP 100-0001 Engineering And Commissioning Manual Download Page 20

TWINFLEX

®

 SRP Control Panel Engineering and Commissioning Manual

 

20 

Fault Relay: C, N/C, N/O 

 

 

The fault relay is derived from a 

single pole change over ‘volt-free’ relay contact which is not fault 

monitored. The maximum contact current rating is 2A @ 24V DC. Inductive loads should be diode 
protected to prevent back EMF causing damage to the relay contact.

  

 

The default setting for the fault relay causes the relay to operate as a 

Common Fault 

output where the 

relay is de-energised in the fault condition and will remain so until the fault is cleared. 

 

Programmable Relays 1-4: C, N/C, N/O 

 

 

 

The relays are derived from a single 

pole change over ‘volt-free’ relay contact which is not fault 

monitored. The maximum contact current rating is 2A @ 24V DC. Inductive loads should be diode 
protected to prevent back EMF causing damage to the relay contact. 

 

 
Programmable relays can be configured to activate during the following system-level states: 

 

OUTPUT STATE 

No State 

 

Manual  

 

Fault 

 

Disablement 

 

Hold 

 

Extract 

 

Release 

 

Pre-Release 

 

Alarm 

 
 

Note:  

 

Programmable  relays  set  to  activate  on  release  must  not  be  used  to  drive  releasing  devices.  The 
circuits connected to these relays are not monitored and will not follow the releasing alarm pattern. 

 

 

When releasing outputs are disabled, Programmable Relays that are set as releasing are also disabled 
but are not logged in the event log as being disabled. 

 
 
 
 
 
 

ON BOARD PCB

FIELD CONNECT IONS

NORMALLY CLOSED

NORMALLY OPEN

COMMON

ON BOARD PCB

FIELD CONNECT IONS

NORMALLY CLOSED

NORMALLY OPEN

COMMON

Summary of Contents for TWINFLEX SRP 100-0001















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands