manualshive.com logo in svg

Fike TWINFLEX SRP 100-0001, Engineering And Commissioning Manual

Share
Download
Fike TWINFLEX SRP 100-0001 Engineering And Commissioning Manual Download Page 17

TWINFLEX

®

 SRP Control Panel Engineering and Commissioning Manual 

 

17 

Ethernet 

 

This port on the panel is reserved for future use.

 

 

Write Protect / Write Enable Switch 

 

The  write  protect  /  write  enable  switch  is  a  two  position  switch  which  is  normally  set  to  stop  options  in  the 
engineer menu from being inadvertently changed.  
Note: when this switch is in the on position the general fault LED will flash to remind the Engineer the switch is 
on. 

 

ON

Switch in

 OFF position

 

 

Write Protect Mode:  

 

In the OFF position, as shown (left), engineering options 

may be viewed but no configuration changes made. 

 
 

ON

Switch in

ON position

 

 

Write Enable Mode: 

 

If configuration changes are to be made, this switch needs 

to be in the ON position as shown (left). 

 
 

 

USB-B 

 

The  panel  is  fitted  with  an  on  board  USB-B  connector.  This  is  to  provide 
communication  via a suitable USB lead to a PC for programming of panel 
options using the TWINFLEX

®

 SRP OSP configuration software. 

 
 

Buzzer Link: J1 

 

Linking J1 will disable the panel buzzer.  The buzzer will remain disabled whilst the link is in place. 

Warning 

– 

To comply with EN54 and BS5839: Pt1: 2002 this link must be left OPEN. 

 

 

LCD Contrast: R4  

 

The LCD contrast may be adjusted by rotating the screw on the variable resistor, located in the upper right hand 
corner  of  the  main  PCB.    Rotate  anticlockwise  to  reduce  the  contrast  (lighten  text).    Rotate  clockwise  to 
increase the contrast (darken text). 

 

 

 

 

Summary of Contents for TWINFLEX SRP 100-0001















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands