Fieldpiece HG3 Field Manual Download Page 26

Page: 26 / 38

www.fieldpiece.com www.fieldpiece.com www.fieldpiece.com www.fieldpiece.com www.fieldpiece.com www.fieldpiece.com www.fieldpiece.com www.fieldpiece.com www.fieldpiece.com www.fieldpiece.com www.fieldpiece.com

5 0

5 1

6.2 CFM INPUT FORM
Inputs

Grille 01

Each grille has a numbered label.

Each grille has an alphanumeric customizable ID.

Flow

Choose Supply or Return.

Manufacturer's Data

This is the free area correction for each grille.

Selections

None

No area is used and CFM cannot be calculated.

No Corrections

No corrections are made and CFM is based on

the size of the grille entered i.e. no grille on duct exit.

Free Area

Use Manufacturer's free area in square feet (sqft),

inches(sqin), centimeters(sqcm), or meters (sdm).

Area Multiplier

Enter the manufacturer's Area Multiplier and grille

dimensions.

Fieldpiece Defaults

Use the Fieldpiece Defaults for grille type and

input size if no manufacturer's data is available.

Velocity

The velocity can only be entered with Fieldpiece airflow accessory

head(s) such as the AAV3. This is for convenience and to ensure accurate

measurements. It allows for multiple measurements per grille. Hold the

vane perpendicular to the grille, set the AAV3 to velocity and press Enter

to start taking the measurement.

Avg

While measuring velocity, press Right Arrow to take additional readings

to get a more accurate average. You can take up to 99 readings per grille.

Add a Grille

Highlight ADD A GRILLE and press Enter.

Customer ID

Used in the file name to save, recall and download tests.

Each grille is labeled with a

number and alphanumeric ID

on the INPUT FORM.

Enter the Manufacturer's

data here or scroll down to

Fieldpiece Defaults. From

there, select the appropriate

default, based on size and

type of grille.

Velocity of air being measured

by the AAV3 Accessory Head.

Highlight Velocity and press

Enter to start measuring.

Traverse the grille slowly and

press the right arrow to take

several measurements to get

an accurate average velocity.

Press Enter to add another

grille to the test. CFM (cubic

feet per minute) is calculated

separately for each grille.

Select Return or Supply for

each Grille.

CFM INPUT FORM.

CFM INPUT FORM continued from above.

Summary of Contents for HG3







































Search results

Summary of Contents for HG3

Reviews:

Related manuals for HG3

Brands by name

Popular brands

Fieldpiece HG3, Field Manual

Search results

Summary of Contents for HG3

Reviews:

Related manuals for HG3

Brands by name

Popular brands