manualshive.com logo in svg

FIC AN19C, Manual, Page: 49 / 55

Share
Download
FIC AN19C Manual Download Page 49

3 - 25

BIOS Setup

field becomes available and you can set which IRQ-X and DMA-X are

assigned to PCI/ISA PNP or Legacy ISA Cards.

Auto:

If your ISA card and PCI cards are all PNP cards, BIOS assigns

the interrupt resource automatically.

PCI/VGA Palette Snoop

This item is designed to overcome problems that can be caused by some

nonstandard VGA cards. This board includes a built-in VGA system that does

not require palette snooping so you must leave this item disabled.

Options: Enabled, Disabled.

Assign IRQ For VGA

This item allows BIOS to assign whether IRQ is with VGA or not.  If you

have not connect the VGA device.  Can release the IRQ for other device.

The default is Enabled.

Options: Enabled, Disabled.

PNP OS Installed

Do you have a PNP OS installed on  your system. The default is No.

Options: Yes, No.

Reset Configuration Data

This setting allows you to clear ESCD data. The default is Disabled

Disabled: Normal Setting.

Enabled: If you have plugged in some Legacy cards to the system and

they were recorded into ESCD (Extended System Configuration

Data), you can set this field to Enabled in order to clear ESCD.

Resources Controlled By

Determines what controls system PNP/PCI resources. The default is Auto

(ESCD).

Manual:

PNP Card’s resources are controlled manually. The IRQ Re-

sources

Summary of Contents for AN19C
























































Reviews:

No comments