manualshive.com logo in svg

FIC AN19C, Manual, Page: 41 / 55

Share
Download
FIC AN19C Manual Download Page 41

3 - 17

BIOS Setup

AC97 Speaker At POST

This item allows you to decide to enable or disable AC97 Speaker At POST

function. The default is Disabled.

Options: Enabled, Disabled.

Game Port Address

Select an address for the Game port.

Options: 201 (default), 209, Disabled.

Midi Port Address

Select an address for the Midi port.

Options: 290, 300, 330, Disabled (default).

Midi Port IRQ

Select an interrupt for the Midi port.

Options: 5, 10 (default).

VIA Onchip LAN (Optional)

Enables the onboard LAN feature. The default is Enabled.

Options: Enabled, Disabled.

Onboard Lan Boot ROM (Optional)

Enables and disables the onboard LAN Boot ROM.  The default is Disabled.

Options: Enabled, Disabled.

High Point IDE RAID

Enables the onboard PCI device High Point IDE RAID.

Options: Auto (default), Enabled, Disabled.

Sil 3112 Serial ATA

Enables the onboard Sil 3112 serial ATA feature.

Options: Enabled, Disabled.

Serial ATA Mode

This item allows to select Serial ATA mode.

Options: IDE, RAID.

Summary of Contents for AN19C
























































Reviews:

No comments