manualshive.com logo in svg

FIC AN19C, Manual, Page: 4 / 55

Share
Download
FIC AN19C Manual Download Page 4

1 - 2

AN19E/AN19C Mainboard Manual

IMPORTANT: AMD CPU HEAT SINK INSTALLATION

Be ware finish heat sink install. Before you boot system, please
check the heat sink is complete contact with die of CPU.

The poor contact will bring about over heat, it may damage your
processor.

It is strongly recommended that at least a 250-watt ATX power pupply
be used for this motherboard. Make sure that your ATX power sup-
ply can supply at least 20 amperes on teh +5-Volt lead and 10mA
on the +5-Volt standby lead (+5VSB). Your system may become
unstable / unreliable and may experience difficulty in powering up if
your power supply is inadequate.

Package Checklist

If you discover any item below was damaged or lost, please contact your

vendor.

þ

The mainboard

þ

   This user manual

þ

FDD cable

þ 

Drivers CD      

þ

ATA-66/100 cable

o

 

 

 

RAID ATA-100 cable (optional)

o

 

 

 

USB cable (optional)

o

 

 

 

I/O shield (optional)

o

 

 

 

Game port cable (optional)

o

 

 

 

SPD650 cable (optional)

o

 

 

 

Serial ATA cable (optional)

o

 

 

 

Bluetooth module (optional)

Summary of Contents for AN19C
























































Reviews:

No comments