FIC AN19C Manual Download Page 3

Page: 3 / 55

1 - 1

Overview

Overview

Chapter 1

The new 1stMainboard

AN19E/AN19C

is an ATX sized motherboard sup-

porting the latest generation of AMD

processors at industry leading speeds.

By utilizing DDR ( Double Data Rate ) transfer rate the 100/133 MHz system bus

effectively reaches Front Side Bus speeds of 200/266/333 MHz. The board

provides users with an ATA133 data transaction for hard drives and has 3

PC1600/PC2100/PC2700 DDR333 DIMMs for up to 3 GB.

The optional serial ATA feature replaces the standard parallel ATA physical

storage interface and allows future enhancements to the computing platform.

It completely software compatible with parallel ATA, requiring no mofication

to your operating system.The board is equipped with 2 dual channeled en-

hanced PCI bus master IDE connectors, plus two optional IDE RAID ATA133

connectors for supporting more efficient data backup.

The board is based around the high performance VIA KT400

as North Bridge

and the VIA VT8235

as South Bridge. Its AGP 8X functions supported AGP

3.0 interface and the most robust 3D games with software environments. The

AGP slot allows 1.5 volt AGP card only and Maximum AGP interface bandwith

2.1 GB/s.

Summary of Contents for AN19C
























































Search results

Summary of Contents for AN19C

Reviews:

FIC AN19C, Manual, Page: 3 / 55

Search results

Summary of Contents for AN19C

Reviews: