manualshive.com logo in svg

FIBARO FGR-223, Operating Manual, Page: 4 / 34

Share
Download
FIBARO FGR-223 Operating Manual Download Page 4

4

InSTAllATIOn

#2: Installation

Connecting the Roller Shutter 3 in a manner inconsistent 

with this manual may cause risk to health, life or material 

damage.

•  connect only in accordance with one of the diagrams,
•  Do not connect Dc powered motors, the device is dedicated to 

operate Ac powered electric motors,

•  Do not connect the device to loads exceeding recommended 

values,

•  The device should be installed in a wall switch box compliant with 

a relevant national safety standards and with depth no less than 

60mm,

•  Electrical switches used in installation should be compliant with the 

relevant safety standards,

•  length of wires used to connect the control switch should not 

exceed 20m,

•  connect roller blind motors with electronic or mechanical limit 

switches only.

!

Notes for the diagrams

:

S1

 - terminal for 1st switch (used to add/remove 

the device)

S2

 - terminal for 2nd switch 

Q2

 - 2nd output terminal for shutter motor

Q1

 - 1st output terminal for shutter motor

L

 - terminal for live lead

N

 - terminal for neutral lead

B

 - service button (used to add/remove the de-

vice and navigate the menu)

Roller

Shutter 3

L

N

S1 S2 Q2

B

Q1

Tips for arranging the antenna

:

•  locate the antenna as far from metal elements as possible 

(connecting wires, bracket rings, etc.) in order to prevent 

interferences,

•  Metal surfaces in the direct vicinity of the antenna (e.g. flush 

mounted metal boxes, metal door frames) may impair signal 

reception!

•  Do not cut or shorten the antenna - its length is perfectly matched 

to the band in which the system operates.

•  Make sure no part of the antenna sticks out of the wall switch box. 

Summary of Contents for FGR-223



































Reviews:

No comments