manualshive.com logo in svg

FIBARO FGR-223, Operating Manual, Page: 14 / 34

Share
Download
FIBARO FGR-223 Operating Manual Download Page 14

14

OPERATInG GATE MOTORS

#7: Operating gate motors

NOTE

Momentary switch

After releasing the 

switch a spring auto-

matically pushes back 

and disconnects the 

switch)

i

The device allows to operate gate motors. 
Gate motor should be connected to Q1 and Q2 terminals according 

to installation diagram. 
When operating gates a momentary switch may be connected to S1 

terminal. 
It is recommended to connect an IR barrier, an emergency stop but-

ton or any alarm mechanism to S2 terminal. Opening a contact in a 

device connected to S2 terminal will always result in stopping a mo-

tor in current position.

Using momentary switch:

click S1 switch – move gate in sequence:
 

OPEn -> STOP -> clOSE -> STOP -> OPEn

Open S2 contact – stop movement

Automatic closing:

•  After full opening – the gate will automatically start closing after 

time specified in parameter 152,

•  After opening S2 contacts – the gate will automatically start clos-

ing after time specified in parameter 154.

Summary of Contents for FGR-223



































Reviews:

No comments