manualshive.com logo in svg

FIBARO FGR-223, Operating Manual, Page: 29 / 34

Share
Download
FIBARO FGR-223 Operating Manual Download Page 29

29

ADVAncED PARAMETERS

150. Force calibration

By setting this parameter to 2 the device enters the calibration mode. 

The parameter relevant only if the device is set to work in positioning 

mode (parameter 151 set to 1, 2 or 4).

Available settings:

0

 - device is not calibrated

1

 - device is calibrated

2

 - force device calibration

Default setting: 

0

Parameter size:

1

 [byte]

151. Operating mode

This parameter allows adjusting operation according to the connect-

ed device.

Available settings: 1 – roller blind (with positioning)

2 – Venetian blind (with positioning)
3 – gate (without positioning)
4 – gate (with positioning)
5 – roller blind with built-in driver
6 – roller blind with built-in driver (impulse)

Default setting: 

1

Parameter size:

1

 [byte]

152. Venetian blind - time of full turn of the slats

For Venetian blinds (parameter 151 set to 2) the parameter deter-

mines time of full turn cycle of the slats. 
For gates (parameter 151 set to 3 or 4) the parameter determines time 

after which open gate will start closing automatically (if set to 0, gate 

will not close). 
The parameter is irrelevant for other modes.

Available settings:

0-90000 

 (0 - 900s, every 0.01s) - time of turn

Default setting: 

150

 (1.5s)

Parameter size:

4

 [bytes]

ROLLER SHUTTER OPERATION CONFIGURATION

Summary of Contents for FGR-223



































Reviews:

No comments