manualshive.com logo in svg

FIBARO FGR-223, Operating Manual, Page: 11 / 34

Share
Download
FIBARO FGR-223 Operating Manual Download Page 11

11

POSITIOnInG cAlIBRATIOn

Calibration using parameter

1.  Make sure:

•  the device is supplied,
•  the device added to the Z-Wave network,
•  parameter 151 is set to 1 or 2.

2.  Set the parameter 150 value to 2
3.  The device will perform the calibration process, completing 

full cycle – up, down and up again

4.  The parameter 150 value will be set to 1 after calibration fin-

ishes.

5.  Test whether the positioning works correctly.

Slats positioning in venetian blinds mode

Calibration using connected momentary switch

1.  Make sure:

•  the device is supplied,
•  momentary switch is connected to S1 and S2 terminals, 
•  the device added to the Z-Wave network,
•  parameter 151 is set to 2,
•  blinds are calibrated.

2.  By default, time of transition between extreme positions is 

set to 150 (1.5 seconds) in parameter 152.

3.  Turn slats between extreme positions by holding   or   

switch:

•   If after full cycle a blind starts moving up or down - de-

crease value of parameter 152,

•  If after full cycle the slats does not reach end positions - 

increase value of parameter 152,

4.  Repeat previous step until satisfactory positioning is 

achieved.

5.  Test whether the positioning works correctly. correctly con-

figured slats should not force the blinds to move up or down.

Summary of Contents for FGR-223



































Reviews:

No comments