background image

13

© Ferno-Washington, Inc.     234-3388-01    June 2008

Limited Warranty Statement

The products sold by Ferno are covered by a limited warranty. 

The actual terms and conditions of the limited warranty, and 

the limitations of liability and disclaimers, are available upon 

request by calling 1.800.733.3766 or 1.937.382.1451.

EMSAR

®

 is the only organization authorized by Ferno to 

manage, service, and repair Ferno products.
Telephone (Toll-free) .......................... 1.800.73.EMSAR
Telephone (Worldwide) .......................... 1.937.383.1052
Fax (Worldwide) ..................................... 1.937.383.1051
Internet.............................................. www.EMSAR.com

REPAIRS OR PARTS 

ferno Customer Relations

Customer  service  and  product  support  are  important 

aspects of each Ferno product. For assistance or infor-

mation:

Canada and the U.s.A.

Telephone (Toll-free) .............................. 1.877.733.0911

Telephone  .............................................. 1.937.382.1451

Fax (Toll-free) ........................................ 1.888.388.1349

Fax  ......................................................... 1.937.382.1191

Internet................................................... www.ferno.com

All Other Locations

For assistance or information, please contact your Ferno 

distributor. If you do not have a Ferno distributor, please 

contact Ferno Customer Relations:
Telephone  ............................................+1.937.382.1451

Fax  .......................................................+1.937.382.6569

Internet................................................... www.ferno.com

Ferno-Washington, Inc.

70 Weil Way

Wilmington, Ohio 45177-9371

European Representative:

Ferno (UK) Limited

Stubs Beck Lane, Cleckheaton

West Yorkshire BD19-4TZ, United Kingdom
Telephone ........................+44 (1274) 851999

Fax...................................+44 (1274) 851111

Internet ...............................www.ferno.co.uk

Accessory Kit 082-2012

Summary of Contents for 082-2012















Reviews: