Ferimex Wireless 802.11g Multi-mode AP User Manual Download Page 32

Page: 32 / 42

USER’S MANUAL OF WLAN ACCESS POINT

Version: 1.1

Enable Remote Log

Log Server IP Address

Click the checkbox to enable remote log service.

Input the remote log IP address

Apply Changes

Click the

Apply Changes

button to save above settings.

Refresh

Click the refresh the log shown on the screen.

Clear

Clear log display screen

3.3.11

Statistics

This page shows the packet counters for transmission and reception regarding

to wireless and Ethernet LAN networks.

Screen snapshot – Statistics

Item

escription

Wireless LAN

Sent Packets

It shows the statistic count of sent packets on the wireless

LAN interface.

Wireless LAN

Received Packets

It shows the statistic count of received packets on the

wireless LAN interface.

Ethernet LAN

Sent Packets

It shows the statistic count of sent packets on the

Ethernet LAN interface.

Ethernet LAN

Received Packets

It shows the statistic count of received packets on the

Ethernet LAN interface.

Refresh

Click the refresh the statistic counters on the screen.

Summary of Contents for Wireless 802.11g Multi-mode AP











































Search results

Summary of Contents for Wireless 802.11g Multi-mode AP

Reviews:

Related manuals for Wireless 802.11g Multi-mode AP

Brands by name

Popular brands

Ferimex Wireless 802.11g Multi-mode AP, User Manual

Search results

Summary of Contents for Wireless 802.11g Multi-mode AP

Reviews:

Related manuals for Wireless 802.11g Multi-mode AP

Brands by name

Popular brands