Felisatti DC10,8L2, Original Instruction Manual

Page: 24 / 94

24
L (Left rotation) : Counterclockwise direction
(for loosening of screw)
R (right rotation) : Clockwise direction
(for fastening of screw, drilling)
Neutral : Rotation lock (for changing the bit)
7. Adjusting the Speed
If drill stalls, it is usually because it is being
overloaded or improperly used. Release
trigger immediately. Do not click trigger on
and off in an attempt to start a stalled drill.
1) Press the switch
The power tool switch allows the speed to
be increased steplessly up to maximum.
2) Move the speed selector switch
1: Low speed, high torque
2: High speed, low torque
8. Torque setting
9. Automatic Spindle Lock
1)Screw work
Selection is feasible from among five setting
anges by force (torgue)
adjustment ring.
low setting range when working with small
screw or at soft working material.
high setting range when working with large
screw or at hard working material.
When the tool is reached at the set torque,
the overload clutch begins to work to keep
the tool in the desired torque. You should
set the desired torque in the practical work.
2) Drilling
Set the torque adjustment ring to the drilling
position.( )
The switch has braking function. When you
release the switch, it brings the motor to a
sudden stop. Also, the surplus rotation will
be stopped.
It is very convenient for fastening screws in
soft materials processed.
The drill spindle is locked when the switch is not
pressed.
This makes quick and easy changing of the tool
in the drill chuck possibble.
10. Battery Protection
When the battery is overheating due to
continuous operation, in order to protect the
battery performance will automatically shut off the
power.
Do not change direction of rotation until
the power tool is at a stand still.
Reversing the rotation direction must be
done only when the tool is switched off.
Reversing the direction during operation
may damage the tool
Always keep tool and air ventage clean for
safe work.
Maintenance
1. Changing tool
The tool and its accessories contain much
raw materials and plastics that can be recycled
after their life. Therefore, plastic parts are
indicated with their material types so that they
can be classified and recycled for each
material type.
For power tool with type Y attachment: if the
replacement of the supple cord is necesary, this
Do not dispose of the battery with home
garbage or into the fire or river.
2.Environmental Protection
4. Y attachment cord
has to be done by the manufactuer or his agent
in order to avod a safety hazard.
It is very dangerous for customers to
troubleshoot or repair the tool for themselves,
Contact the nearest A/S center (sales agency)
and request for a service
The repair shall be requested to the
qualified electric speciailst.
If the replacement of the supply cord is
necessary. this has to be done by the
manufacturer or his agent in order to avoid a
safety hazard.
3. What to do when the tool does not work normally
6. Reversing the Rotation Direction
Pulling the switch trigger will turn on
the LED light
Figure 10
Figure 9
Figure 8
5. Work light
Figure 7
Take care not to short-circuit the terminal of
the battery. The short-circuit of the terminal
may cause a fire or explosion doing a
serious personal injury.
2. Charging process
1) Charging indication
Green Blinks : Before charging
Red Lights : While charging
Green Lights : Charging completed
Red Blink : Overheat standby
(Battery overheated)
Yellow Blinks : Charging impossible
2) If charging of the heated battery is attempted
immediately after it has been used or
charged, indicator blinks in red (overheat
standby). After the cooling, indication
changes to red glowing and charging begins.
3) This charger detects charging status of the
batery and always keeps the battery in full
charge state.
Use only the specified battery and battery
charger. Otherwise battery and charger can
be damaged by fire, explosion,charging
error or overheat.
Be sure to unplug the charger after finishing
the charging.
3. Installing and removing battery
1) Installing.
Set the rotational direction switch at center
position (locked state).
Insert the charged battery into the slot
below the handle until the battery securely
latched with a click.
2) Removing.
Push the battery button once and take it
out to remove it.
4. Charge state of the battery
Pulling the switch trigger will turn on the
battery level indicator for about 2 seconds.
1 = Battery 70 - 100% charged
2 = Battery 30 - 69% charged
3 = Battery less than 30% charged
4 = Battery flat of defective
(Blinking/Turn off)
Always set the rotational direction switch at
center position when inserting the battery
or changing, carrying or storing the tool.
Figure 4
Figure 5
Figure 6
Figure 11
1) Mounting the Bit
Pull the lock sleeve forward.
Insert a screw driver bit into the tool
holder to the end and release the lock
sleeve.
2) Removing the bit
Keep the lock sleeve pressed forward
while taking out the bit.
Before you change the tool, you must remove
the battery from the body of the electric drill or
set the rotational direction swith in lock position
(neutral position).