FarmTek Growers Supply GrowSpan Gothic Pro 106306D Assembly Instructions Manual Download Page 49

Page: 49 / 53

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 06.07.18

H-CHANNEL

INST

ALLA

TION INSTRUCTIONS

The new H-channel design requires installation of the flat side facing out with channel side toward the building. Some diagrams

and photos in this document show installation of

original

H-channel with channel side facing out. Design of new H-channel

does not allow

channel-side out installation.

Use the diagrams on this page to install H-channel with flat side facing out.

ATTENTION:

Use only 1-1/2"

Tek screws to

attach H-channel to building frame.

Do not use

shorter screws. They will not hold. Do not use washers on T

ek screws when installing

H-channel.

ATTENTION:

Install all twin-wall polycarbonate panels with UV

-protected side toward the sun.

-protected side toward sun.

Install 1-1/2"

Tek screws through

H-channel into building frame.

H-Channel

Center Groove

Flat side toward the sun.

Flat Side

Channel

Summary of Contents for Growers Supply GrowSpan Gothic Pro 106306D






















































Search results

Summary of Contents for Growers Supply GrowSpan Gothic Pro 106306D

Reviews:

Related manuals for Growers Supply GrowSpan Gothic Pro 106306D

Brands by name

Popular brands

FarmTek Growers Supply GrowSpan Gothic Pro 106306D, Assembly Instructions Manual

Search results

Summary of Contents for Growers Supply GrowSpan Gothic Pro 106306D

Reviews:

Related manuals for Growers Supply GrowSpan Gothic Pro 106306D

Brands by name

Popular brands