FarmTek Growers Supply GrowSpan Gothic Pro 106306D Assembly Instructions Manual Download Page 17

Page: 17 / 53

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 06.07.18

15. Using the marks on the base tube for the rough

opening for the door, attach the bottom of each vertical

frame member to the base tube using an angle bracket.

Consult the end frame diagram.

INSTALL THE END WALL FRAME (continued)

16. With the vertical door frame tubes attached at the

bottom and loose at the top, measure each frame

member to locate the height of the rough door opening

and mark the location on the inside of the door frame.

Consult the End Frame Diagrams Quick Start section

located at the back of these instructions.

Frame shown may differ from actual frame.

17. Using a level (or other means), verify that one vertical

door frame tube is plumb and tighten the band clamp

bolt to lock the first door frame member in place.

18. Choose the square tube for the door frame header and

cut the swaged end to the proper length for the width of

the rough door opening.

19. Using two angle brackets, attach the header tube to

the end wall assembly between the vertical door frame

tubes as shown.

Inside dimensions are shown. Diagrams may show a

different frame used for illustration purposes only.

20. Verify that both door frame verticals are plumb and

recheck the width of the rough door opening at the top

and bottom. Adjust if needed.

21. Cut the metal tube for the short, end wall supports

(positioned between the header and the end rafter) and

attach as shown in the following diagram.

92-1/4"

Mark Here

Height of rough

door opening

Header

Height of rough

door opening

92-1/4"

96-3/4"

Width

Door Opening

Angle Bracket

Mark

Base Tube

Center of

Door Frame

Tube

Summary of Contents for Growers Supply GrowSpan Gothic Pro 106306D






















































Search results

Summary of Contents for Growers Supply GrowSpan Gothic Pro 106306D

Reviews:

Related manuals for Growers Supply GrowSpan Gothic Pro 106306D

Brands by name

Popular brands

FarmTek Growers Supply GrowSpan Gothic Pro 106306D, Assembly Instructions Manual

Search results

Summary of Contents for Growers Supply GrowSpan Gothic Pro 106306D

Reviews:

Related manuals for Growers Supply GrowSpan Gothic Pro 106306D

Brands by name

Popular brands