FarmTek Growers Supply GrowSpan Gothic Pro 106306D Assembly Instructions Manual Download Page 7

Page: 7 / 53

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 06.07.18

End Rafter

Interior

Rafter

Baseboard is

supplied by

customer.

Ground

Level

ATTENTION:

Position purlins evenly during the

frame assembly. Use the rafter pipe joints as

guides when installing the end clamps, cross

connectors, and purlins.

Purlins

Ground

Post

Ribbon

Board

OVERVIEW

This section is an overview of the process for assembling

your Gothic Pro Greenhouse. For details, please

see section, Assembling the Gothic Pro Greenhouse

Components. See illustration below to identify main parts of

greenhouse.
1.  Locate the required parts for each assembly procedure.
2.  Assemble the rafters and frame, and square the frame.
3.  Prepare and attach end panels.
4.  Attach main cover and Twist-of-the-Wrist assembly.

GrowSpan

™

Gothic Pro Greenhouses and Systems

Summary of Contents for Growers Supply GrowSpan Gothic Pro 106306D






















































Search results

Summary of Contents for Growers Supply GrowSpan Gothic Pro 106306D

Reviews:

Related manuals for Growers Supply GrowSpan Gothic Pro 106306D

Brands by name

Popular brands

FarmTek Growers Supply GrowSpan Gothic Pro 106306D, Assembly Instructions Manual

Search results

Summary of Contents for Growers Supply GrowSpan Gothic Pro 106306D

Reviews:

Related manuals for Growers Supply GrowSpan Gothic Pro 106306D

Brands by name

Popular brands