background image

11

GROWSPAN

 GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 06.07.18

FRAME ASSEMBLY (continued)

4.  From the location marked in the previous step, 

measure forty-eight inches (48") and make another 

mark on the assembled purlin.

5.  Continue to mark the purlin in 48" intervals until all 

locations are marked. These marks help to maintain 

the 48" on-center rafter spacing of the shelter during 

assembly.

6.  Repeat this procedure until all assembled purlins are 

marked.

7.  After assembling all rafters and pre-marking the purlins, 

assemble the frame.

ASSEMBLE THE FRAME
After all ground posts are driven in place, rafters are 

assembled and purlins pre-marked, assemble the frame.

Gather the Parts:
•  All Rafter Assemblies and Pre-marked Purlins
•  Band Clamps (#QH1402)
•  Cross Connector (#102548)
•  5/16" x 2-1/2" Machine Bolts and 5/16" Nuts 
•  Lifts, ladders, and assistants
•  Rope or cable

 

1.  Carefully stand the 

first end rafter

slide a band clamp 

onto each rafter leg

, and place the leg pipes in the first 

set of ground posts.  

 

Brace the rafter in place to keep it straight. Depending 

on the frame size, a lift and additional assistants may 

be needed. Consult Quick Start section for details. 

 

Rafter shown differs in design.

2.  Secure the leg pipes to the ground posts using the 

5/16" x 2 1/2" machine bolts and nuts.  

Rafter shown differs in design.

ATTENTION:

 Stand the rafter so the nuts and bolts of 

the end clamps are to the inside of the frame.

3.  Use rope or cable to keep the rafter in position. 

4.  Carefully position the first interior rafter in place and 

secure the leg pipes to the ground posts.

Rafter shown differs in design.

1st Interior Rafter

End Rafter

Inside of 

Shelter

Outside of 

Shelter

Rafter

Ground 

Post

Band 

Clamp

Summary of Contents for Growers supply GrowSpan 106306PC




















































Reviews: