FarmTek Growers supply GrowSpan 106306PC Installation Instructions Manual Download Page 6

Page: 6 / 51

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 06.07.18

H-CHANNEL INSTALLATION INSTRUCTIONS

The new H-channel design requires installation of the flat side facing out with channel side toward

the building. Some diagrams and photos in this document show installation of

original

H-channel with

channel side facing out. Design of new H-channel

does not allow

channel-side out installation.

Use the diagrams on this page to install H-channel with flat side facing out.

ATTENTION:

Use only 1-1/2" Tek screws to attach H-channel to building frame.

Do not use

shorter screws. They will not hold. Do not use washers on Tek screws when installing

H-channel.

ATTENTION:

Install all twin-wall polycarbonate panels with UV-protected side toward the sun.

UV-protected side

toward sun.

Install 1-1/2" Tek screws through

H-channel into building frame.

H-Channel

Center Groove

Flat side toward the sun.

Flat

Side

Channel

Summary of Contents for Growers supply GrowSpan 106306PC




















































Search results

Summary of Contents for Growers supply GrowSpan 106306PC

Reviews:

Related manuals for Growers supply GrowSpan 106306PC

Brands by name

Popular brands

FarmTek Growers supply GrowSpan 106306PC, Installation Instructions Manual

Search results

Summary of Contents for Growers supply GrowSpan 106306PC

Reviews:

Related manuals for Growers supply GrowSpan 106306PC

Brands by name

Popular brands