manualshive.com logo in svg

Farm Fans C-21100B, Owner'S Manual, Page: 43 / 66

Share
Download
Farm Fans C-21100B Owner'S Manual Download Page 43

41

Fig. 7-1   Meter roll pan cleanout

mrpan.tif

lever in locked position

lever in open position

closure door "closed"

TRIPCLEN.DSF

closure door "open"
(would normally hang vertically)

To "fast dump" grain, swing 
levers downward. To close,
swing door closed and pull 
lever upward into locked
position.

Fig. 7-2   Fast-trip cleanout assembly

SERVICE TIP:  Open cleanout doors at end of season and
remove debris.  Doors may be left open during the off sea-
son for better drainage.

To “fast dump” grain,
swing levers down-
ward. To close, swing
door closed and pull
lever upward into
locked position.

Closure door “closed”

Closure door “open” (would normally
hang vertically)

Lever in locked position

Lever in open position

Seasonal Inspection and Service

At the end of a drying season, between dryer runs, or
when changing from one crop to another it is IMPOR-
TANT to dump any excess grain off of the meter roll
pan after the dryer has been emptied for the following
reasons:
1. Grain not dumped off of the meter roll pan will conta-
minate the next crop that is dried.
2. Grain left over could also draw moisture and stick to
the pan. This condition could cause a boundary layer to
form in the column and prevent grain from sliding
smoothly into the meter roll.
3. A boundary layer could also be formed if the dryer is
allowed to set partially full. For example, if the left over
grain were to get rained or snowed on. 

TO DUMP THE METER ROLL PAN:
1. Pull the hitch pin that locks the pan in the operating
position as shown in the diagram. 
2. Shove up on the actuator arm as shown.  (The pan
may resist movement at first and the operator may
need to pound up on the arm at first to break the pan
loose.)  
3. Once the pan has started to move continue to shove
up on the arm until you feel the pan make contact with
the meter roll.  This will ensure that all excess grain has
been dumped off the pan. 
4. Return the pan to its operating position and be sure
to put the hitch pin back in.  If the hitch pin is left out
the pan may not stay completely down in the operating
position during filling of the dryer causing flow problems
in the column and into the meter roll.  

SERVICE TIP:
It is a good idea to leave the meter roll pan in the up or
dump position during the off-season to allow any foreign
material that may get into the column to fall through into
the auger trough, thus not obstructing the meter roll
opening upon start up.

ATTENTION!

REMEMBER TO PULL THE PAN DOWN INTO THE
OPERATING POSITION AND PUT THE HITCH PIN
BACK IN BEFORE LOADING.

HINGED FAST-TRIP CLEANOUT

The dryer is factory equipped with a "fast-trip"
cleanout mechanism beneath the unload auger, as
shown in Fig. 7-2.  The individual fast-trip doors allow
easy cleanout of accumulated materials.

Summary of Contents for C-21100B



































































Reviews:

No comments