fann 100072577 User Manual Download Page 3

Page: 3 / 73

Cement Curing Autoclave User Manual

100072577

Revision H

Contents

Introduction ............................................................................................................. 1

1.1 Cement Curing Autoclave ................................................................................... 1

1.2 Function ............................................................................................................... 1

1.3 Features ................................................................................................................ 2

Safety ....................................................................................................................... 4

2.1 Machine Hazards ................................................................................................. 4

2.2 Ergonomic Considerations ................................................................................... 5

Features and Specifications .................................................................................. 6

3.1 Cement Curing Autoclave Mechanical ................................................................ 6

3.2 Cement Curing Molds .......................................................................................... 7

3.3 Cement Curing Autoclave Controls and Indicators ............................................. 9

3.4 Temperature Controller Configuration .............................................................. 10

3.5 Pressurizing the Cement Curing Autoclave ....................................................... 24

Installation ............................................................................................................. 26

4.1 Parts of the Cement Curing Autoclave .............................................................. 26

4.2 Other Parts ......................................................................................................... 26

4.3 Locating the Cement Curing Autoclave ............................................................ 26

4.4 Electric Power Supply ....................................................................................... 26

Operation ............................................................................................................... 28

5.1 Sample Preparation ............................................................................................ 28

5.2 Prepare the Cube Mold ...................................................................................... 28

5.3 Prepare the Cement Slurry ................................................................................. 32

5.4 Fill the Molds ..................................................................................................... 32

5.5 Place molds into chamber .................................................................................. 35

5.6 Place chamber in heating jacket......................................................................... 39

5.7 Pressurize the chamber ...................................................................................... 41

5.8 Running a test .................................................................................................... 41

5.9 Ending the test ................................................................................................... 43

5.10 Remove the chamber ......................................................................................... 43

5.11 Cleaning the molds, pressure chamber, and autoclave ...................................... 44

Analyzing Results ................................................................................................. 45

Troubleshooting and Maintenance ...................................................................... 46

Summary of Contents for 100072577










































































Search results

Summary of Contents for 100072577

Reviews:

Related manuals for 100072577

Brands by name

Popular brands

fann 100072577, User Manual

Search results

Summary of Contents for 100072577

Reviews:

Related manuals for 100072577

Brands by name

Popular brands