fann 100072577 User Manual Download Page 51

Page: 51 / 73

Cement Curing Autoclave User Manual

100072577

Revision H

5.11

Cleaning the molds, pressure chamber, and autoclave

5.11.1

Wipe all cement remnants and grease from the molds, lid and inside

of the chamber body. Pay particular attention to clean the threads and the
O-ring groove in the lid.

5.11.2

Remove cement particles using a metal spatula or wire brush.

5.11.3

Remove any cement film by dipping the part in 15-20 percent

hydrochloric acid. Let the parts sit for several minutes, then brush clean
and rinse the parts thoroughly with water. Properly disposed of the waste
acid.

5.11.4

Remove grease film with a solvent

5.11.5

Carefully dry the parts.

5.11.6

Inspect the lid O-ring for damage, and replace those which are

damaged.

5.11.7

Clean and wipe all surfaces on the Cement Curing Autoclave.

Summary of Contents for 100072577










































































Search results

Summary of Contents for 100072577

Reviews:

Related manuals for 100072577

Brands by name

Popular brands

fann 100072577, User Manual

Search results

Summary of Contents for 100072577

Reviews:

Related manuals for 100072577

Brands by name

Popular brands