fadini Elpro 43 Manual Download Page 9

Page: 9 / 32

ELECTRONIC CONTROLLER FOR DARDO 430 GATE OPERATOR

ON DOUBLE SWINGING GATES

Elpro 43

Meccanica Fadini s.n.c.

Responsible Manager

CE DECLARATION OF CONFORMITY of the manufacturer:

Meccanica Fadini snc (Via Mantova, 177/A - 37053 Cerea - VR - Italy) declares under own responsibility that

Elpro 43

complies with the 2006/42/CE Machinery Directive,

and also that it is sold to be installed in an “automatic system”, along with original accessories and components as indicated by the manufacturing company, that is not
liable for any possible incorrect use of the product. The product complies with the following specific norms: Low Voltage Directive 2014/35/UE, Electromagnetic
Compatibility Directive 2014/30/UE. In order to certify the product, the Manufacturer declares under own responsibility the compliance with the EN 13241-1 PRODUCT
NORMS.

TROUBLE SHOOTING IN CASE OF FAILURE

- Make sure that power supply to the controller be 230 V ±10%
- Check all the fuses
- Check the photocells contact, it must be normally closed
- Make sure that no voltage drop be occurring between the control board and
the electric motor
- Check all the NC contacts in the control board

NOTE WELL:

All the possible connections to the control board terminals are also illustrated
in the respective instructions provided with the individual accessories.

IMPORTANT FOR THE INSTALLATION AND PROPER FUNCTIONING:

- The controller is to be installed in a sheltered, dry place; holes are provided for fixing into FADINI universal box and into any commercial one.
- Make sure that power supply to the electronic controller be 230 V ±10%.
- In case of distances superior than 50 meters, increase the wire section.
- Fit the power supply to the controller with a 0,03 A, high sensibility, magneto-thermal circuit breaker.
- For the power supply, electric motor and flasher use1,5 mm² section wires up to 50 m of distance.
- For the limit switches, photocells, command switches and accessories use 1 mm² section wires.
- If no stop button is used bridge terminals 3 and 6.
N.W.: for applications such as lights control, CCTV, etc. use solid state relays to prevent interference with the microprocessor.

DIAGNOSTICS BY LEDs:
L0 (Green ON)

= Pair of photocells fitted inside, no obstacle detected

L2 (Green ON)

= Pair of photocells closing, no obstacle detected

(Red OFF) = Open, switches ON when a command pulse to open is given

(Red OFF) = Close, switches ON when a command pulse to close is given

L6 (Green ON)

= Stop, switches OFF when a command pulse to stop is given

(Red OFF) = Radio, switches ON when a transmitter button is pulsed

and the radio contact is made on terminals 3 and 7

(Red OFF) = It illuminates in case of short circuit with 24 Vdc.

It switches OFF when the short circuit fault is removed

L13 (Green ON)

= Safety edge open, switches OFF whenever the safety edge

is engaged

L14 (Green ON)

= Safety edge close, switches OFF whenever the safety edge

is engaged

L16

(Red OFF)

= Switches ON whenever a pedestrian command is given

E1 (Red ON)

= Encoder led

E2 (Red ON)

= Encoder led

General description:

the electronic controller ELPRO 43 has been designed to control the gate operator type

DARDO 430

at 230 Vac, mounted on single- or double-

swinging gates. 230 V - 50 Hz single-phase power supplied. The manufacturer is not liable for incorrect use of the controller, and reserves also the right to change and
update it to the latest standards of the art at any time.

green led, must be
ON all the time

red led OFF all the time, it goes ON
when a contact is made or a pulse given

red led ON

red led flashing:
controller on programming phase, waiting
for a pulse by the programming button

TRANSFORMER

1 2 3 4 5 6 7 8 9 10

PLUG-IN
RADIO

CARD
CONNECTOR

phot

ells

closing

radio c