background image

Read this before you begin installation-

Check all parts to the parts list above before beginning installation. If any parts are missing contact Fabtech at 909-597-7800 
and a replacement part will be sent to you immediately.

Read all instructions thoroughly from start to finish before beginning the installation. If these instructions are not properly 
followed severe frame, driveline and / or suspension damage may occur. 

Check your local city and state laws prior to the installation of this system for legality. Do not install if not legal in your area.

Prior to the installation of this suspension system perform a front end alignment and record. Do not install this system if the 
vehicle alignment is not within factory specifications. Check for frame and suspension damage prior to installation.

The installation of this suspension system should be performed by two professional mechanics.

Use the provided thread locking compound on all hardware. 

Do not combine this suspension system with any other lift device or parts.

This suspension must be installed with Fabtech shock absorbers.

WARNING- Installation of this system will alter the center of gravity of the vehicle and may increase roll over as compared  
to stock.

For technical assistance call:  909-597-7800 or e-mail:  [email protected]

Fabtech replacement driveshafts are required with this system. Due to the different shafts for the 2-door and 4-door models, the 
driveshafts are sold separately. See chart below for proper driveshafts for your model of Jeep.

Steps 13-16 are for the modification of the exhaust pipe on 2012-15 models and require FTS94060 loop delete pipe not included 
in this kit or have a local muffler shop replace the cut out section of pipe from steps 13-14.

Factory rocker guards may need to be adjusted and/or trimmed to run 37” tires.

Recommend Tires and Wheels:

Use 37/12.50R17 tire w/ 17x8.5 wheels w/ 5” BS w/ minor trimming

- PRE-INSTALLATION NOTES -

4 of 31

FTS94057

2007-15 Front Driveshaft 2/4 Door

FTS94051

2007-11 Rear Driveshaft 2 Door Only

FTS94052

2007-11 Rear Driveshaft 4 Door Only

FTS94058

2012 - UP Rear Driveshaft 2 Door Only

FTS94059

2012 - UP Rear Driveshaft 4 Door Only

Summary of Contents for FTS24094
































Reviews: