background image

X 1

X 1

P

X 1

X 2

P

ON

P

ENGLISH

6

4  MEMORY STORING THE FIRST RADIO 

UP

DOWN

STOP /

PREFERRED POSITION

PROGRAMMING 

PUSH-BUTTON

1) Supply power to the motor.

2) The motor performs a brief movement in both direction to confirm the memory is empty.

3) Within 10 seconds, press the programming push-button “P” for 2 seconds and within the following 10 seconds, press 

the stop/preferred position push-button.

4) The motor performs two brief movements in both directions to confirm the performed memory storing.

WITHIN 10 SECONDS

2 seconds

 1 )   D U R I N G   T H E   M E M O RY   S T O R I N G   P H A S E   O F   T H E   F I R S T   R E M O T E   C O N T R O L   A N D   T I L L   T H E   E N D   O F 

T H E   S E T- U P   P R O C E D U R E ,   T H E   M O T O R   O P E RAT E S   I N   D E A D - M A N   M O D E .   ( P U S H - B U T T O N   H E L D   D O W N ) 
2) BEFORE COMPLETING THE SET-UP, THE MOTOR COULD ROTATE IN THE OPPOSITE DIRECTION TO THE GIVEN COMMAND (E.G.: YOU 
PRESS THE UP PUSH-BUTTON AND THE ROLLING SHUTTER LOWERS); AT THE END OF THE SET-UP, THE UP OR DOWN PUSH-BUTTONS 
ARE AUTOMATICALLY MATCHED TO THE CORRECT DIRECTION OF ROTATION.

Fig.8

Fig.9

WITHIN 10 SECONDS

5  SET-UP (SETTING THE TRAVEL LIMITS)

The SET-UP procedure enables you to set, by pressing the connected push-buttons, the up and down travel limit 

and the correct functions for the rolling shutter to be motorised (ROLLING SHUTTER MODE, STANDARD AWNING MODE 

AND CASSETTE AWNING MODE).

The SET-UP procedure can only occur in AUTOMATIC mode (with two modes) or in MANUAL mode.

The 

AUTOMATIC SET-UP

 is possible for rolling shutters only,

The 

MANUAL SET-UP 

is possible for all applications (ROLLING SHUTTER, STANDARD AWNING OR CASSETTE AWNING).

2 seconds

REAR 

VIEW

  MAX. 20 RADIO DEVICES CAN BE STORED IN THE MEMORY OF THE MOTOR INTERNAL RECEIVER (WALL-MOUNTED REMOTE CONTROLS, 

RADIO ANEMOMETERS, ETC.). MEMORY STORING CAN OCCUR IN ANY MOTOR STATUS.

  IF THE SUN SENSOR IS ENABLED ON THE MOTOR, THE COMMANDS SENT BY ANY ALREADY MEMORY-STORED REMOTE CONTROL ARE 

INHIBITED; DISABLE FIRST THE SUN SENSOR USING THE REMOTE CONTROL.

Portable remote control 

Wall-mounted remote control

CHANGE RADIO 
CHANNEL

ENABLE                                 
DISABLE 
SUN SENSOR

Summary of Contents for T-MODE TM 35 ER



























Reviews: